Quadra-Fire QUADRA-FIRE CONTOUR - Manual
Quadra-Fire QUADRA-FIRE CONTOUR – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Contour Pellet Stove; Aladdin Hearth Products
- Page 3 – October 10, 2001 3; TABLE OF CONTENTS; Page; CONTOUR Pellet Stove
- Page 4 – October 10, 2001 4; SAFETY LABEL; BEHIND
- Page 5 – October 10, 2001 5; LISTINGS AND SPECIFICATIONS; The QUADRA-FIRE CONTOUR pellet stove is safety listed; See pages 5 and 9 for mobile home installation; *BTU output will vary, depending on the brand of; DIMENSIONS
- Page 6 – October 10, 2001 6; CHIMNEY AND EXHAUST CONNECTION; When running vertically with pellet venting, the following; VENTING GRAPH; The table below can help you determine the equivalent; VENTING PIPE TABLE
- Page 7 – October 10, 2001 7; The Quadra-Fire Contour is approved for; Straight Out; VENTING SYSTEMS
- Page 8 – October 10, 2001 8
- Page 9 – TOP VENT FLUE ADAPTER INSTALLATION; Wing Nut; FIGURE 1
- Page 10 – LOG SET PLACEMENT INSTRUCTIONS; Due to the abrasive nature of a pellet stove fire, the; PIECE LOG SET INSTALLATION
- Page 11 – MOBILE HOME INSTALLATION; FUEL SIZE AND MATERIAL; OPERATING INSTRUCTIONS
- Page 12 – START YOUR FIRST FIRE; See; GENERAL OPERATION INFORMATION; HEAT OUTPUT CONTROLS
- Page 13 – FIREBOX ASH REMOVAL; NOTE: Embers remain hot for many days.; CLEANING AND MAINTENANCE; Refer to Top Baffle Removal
- Page 14 – THESE BLOWERS REQUIRE NO LUBRICATION.; READING THE FIRE AND ADJUSTMENT; CLEANING AND MAINTENANCE CONT'D
- Page 15 – October 10, 2001 15; COMPONENT INFORMATION
- Page 16 – October 10, 2001 16; NOTE: Do not open the control box. This
- Page 17 – October 10, 2001 17
- Page 18 – October 10, 2001 18; TROUBLESHOOTING
- Page 19 – October 10, 2001 19
- Page 20 – October 10, 2001 20; LARGE FIRE, ASH BUILDUP AND DIRTY; b. Visually check the cleanliness of the firebox, the; WIRING HARNESS
- Page 21 – Parts Included in Kit:; Snip corners and remove plate.; Attach Collar; Outside Air Kit Instructions
- Page 22 – NOTE: The holding tabs on the back side of the but-; TRIM RING INSTALLATION INSTRUCTIONS
- Page 23 – Gold Grille Installation Instructions; KIT CONTENTS
- Page 24 – Exhaust Blower Replacement Instructions; Phillips Screwdriver Flathead; FEED MOTOR Replacement Instructions
- Page 25 – October 10, 2001 25; Rear Screen Replacement Kit Instructions; ONLY; Rear Replacement Screen; TOP BAFFLE REMOVAL INSTRUCTIONS; the heat exchanger scraper rods are pulled; See FIGURE 1; Lower mounting
- Page 26 – October 10, 2001 26; SERVICE PARTS
- Page 27 – October 10, 2001 27; Lifetime Warranty
- Page 28 – PLEASE RETURN THESE
1445 N. Highway
Colville, WA 99114
www.aladdinhearth.com
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY NOTES
1. When installing your stove, particular attention should be paid to fire protection. If this unit is not properly installed, a house
fire may result. For your safety, follow the installation instructions, and contact local building or fire officials about restrictions
and installation inspection required in your area.
2. Read power supply section of component information (page 15) before you plug in the stove.
3. Always unplug the stove before cleaning or servicing.
4. During operation, if any part of the stove starts to glow, the stove is in an overfired condition. Reduce the feed rate and increase
the amount of air going into the stove. OVERFIRING VOIDS WARRANTY.
5. Do not install a flue damper in the exhaust venting system of this unit.
6. Do not connect the stove to a chimney flue already serving another appliance.
7. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or freshen up a fire in
this heater. Keep all such liquids well away from the heater while it is in use.
8. The stove operates with a negative pressure firebox and a positive pressure exhaust. It is imperative that the chimney system
be airtight and installed correctly.
9. Dispose of all ashes in a metal container.
10. Comply with all minimum clearances to combustibles as shown on page 5.
11. The Quadra-Fire Contour is tested and approved for pelleted biomass fuel or shelled field corn only. Burning of any other
type of fuel voids your warranty!
12. Aladdin Hearth Products, manufacturer of the Contour pellet stove, reserves the right to alter its products, their specifications
and/or price without notice.
13. ALADDIN HEARTH PRODUCTS, GRANTS NO WARRANTY, IMPLIED OR STATED, FOR THE INSTALLATION OR
MAINTENANCE OF THIS UNIT AND ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
CONTOUR PELLET STOVE
INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS
Please read this entire manual before installation and use of this pellet fuel room heater.
Failure to follow these instructions could result in property damage, bodily injury or even death.
O - T L
Tested and
Listed by
Beaverton
Oregon USA
OMNI-Test Laboratories, Inc.
C
PRIOR TO FIRST FIRE
: Remove all labels from glass. Clean gold surfaces with a glass cleanser and soft cloth
to prevent staining from fingerprint oils.
IMPORTANT! Record serial number of your stove on the warranty card and mail immediately.
The serial number is located on the safety label affixed behind the left side curtain on
the outside of hopper wall.
250-5583 October 10, 2001
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
October 10, 2001 2 250-5583 Contour Pellet Stove Aladdin Hearth Products welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality, durability, and performance. This commitment begins with our research of the market, including ‘...
October 10, 2001 3 250-5583 Contour Pellet Stove TABLE OF CONTENTS Page Safety Label......................................................... 4Safety Label Location.............................................4Clearances to Combustibles................................ 5Floor Protection Requirements....
Note 1: In residential installations, when using parts #811-0860, (3" - 3" Top Vent Adapter) and #812-3570 (3" - 6" Offset Adapter), 24 gauge 6" single wall flue connector may be used. Note 2: In manufactured home installation, when using part #811-0860, (3" - 3" Top Vent...
