Grizzly Industrial T27417 - User Manual

-4- Model T27417 (Mfd. Since 09/15) Controls & Components Refer to Figures 1–5 and the following descrip- tions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and stay safe whe...

Model T27417 (Mfd. Since 09/15) -5- Table & Dust Port Figure 4. Location of table components and dust port. M K K. Table Tilt Lock Knob (1 of 2): Tighten to secure table tilt setting. L. Dust Port: Connects to dust collection sys- tem (not included). M. Work Table: Supports workpiece during sand...

-6- Model T27417 (Mfd. Since 09/15) Machine Data Sheet The information contained herein is deemed accurate as of 7/12/2016 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF...

-8- Model T27417 (Mfd. Since 09/15) ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always d...

-10- Model T27417 (Mfd. Since 09/15) Additional Safety for Spindle /Edge Sanders Serious injury or death can occur from fingers, clothing, jewelry or hair getting entangled in rotating spindle or other moving components. Abrasion injuries can occur from touching rotating sanding drum with bare skin....

Model T27417 (Mfd. Since 09/15) -11- SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize...

Model T27417 (Mfd. Since 09/15) -13- SECTION 3: SETUP This machine was carefully packaged for safe transport. When unpacking, separate all enclosed items from packaging materials and inspect them for shipping damage. If items are damaged, please call us immediately at (570) 546-9663. IMPORTANT: Save...

-14- Model T27417 (Mfd. Since 09/15) Site Considerations Figure 8. Minimum working clearances. 18½" 16½" 1½" Dust Port Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent u...

Model T27417 (Mfd. Since 09/15) -15- Assembly Place the spindle nut, table inserts, sanding drums and sleeves, spindle washers, edge-sand-ing attachment, and spindle nut wrench in the appropriate accessory slots beneath the table (see Figures 11–12). A sanding drum does not need to be installed unti...

-16- Model T27417 (Mfd. Since 09/15) Test Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and f...

Model T27417 (Mfd. Since 09/15) -17- SECTION 4: OPERATIONS Disabling Switch The switch can be disabled by removing the key, as shown below. Disabling the switch in this man-ner can prevent unauthorized operation of the machine, which is important if it is not kept inside an access-restricted buildin...

-18- Model T27417 (Mfd. Since 09/15) Spindle Sanding 3. Place table insert in table opening, then install desired sanding drum on spindle shaft, followed by corresponding sanding sleeve and throat plate (see Figure 17). 4. Secure sanding drum with appropriate spin- dle washer and spindle nut (see Fi...

Model T27417 (Mfd. Since 09/15) -19- 1. DISCONNECT MACHINE FROM POWER! 2. Remove spindle sanding components in reverse order of installation (see Figure 17 on Page 18). 3. Clean openings for table insert, throat plates, and any other spindle areas as necessary. There should be no sawdust on ledge of...

-22- Model T27417 (Mfd. Since 09/15) Bevel Sanding The work table on Model T27417 tilts from 0°–45° for sanding bevels on your workpiece. The table tilt stop bracket (see Figure 25) has detents for quickly setting the most common angles: 0°, 15°, 22.5°, 30°, and 45°. Note: You can bevel sand using e...

Model T27417 (Mfd. Since 09/15) -23- SECTION 5: ACCESSORIES ACCESSORIES Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to o...

Model T27417 (Mfd. Since 09/15) -25- SECTION 6: MAINTENANCE Schedule To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service. Cleaning the Model T27417 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the r...

-26- Model T27417 (Mfd. Since 09/15) Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your ma...

Model T27417 (Mfd. Since 09/15) -33- SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before...

-36- Model T27417 (Mfd. Since 09/15) Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PT27417001 HEX NUT M8-1.25 50 PT27417050 RUBBER GASKET 2 PT27417002 BALL BEARING 6004ZZ 51 PT27417051 SPINDLE WASHER 3 PT27417003 DRUM WHEEL 3" X 4", ALUMINUM 52 PT27417052 BEARING SLEEVE 4 P...

-38- Model T27417 (Mfd. Since 09/15) Labels Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...