Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................................................................................................... 2 Contact Info .................................................................................................................................
Page 4 - INTRODUCTION; Contact Info; Manual Accuracy
-2- Model G9717 (Mfd. Since 3/00) INTRODUCTION We stand behind our machines! If you have ques-tions or need help, contact us with the information below. Before contacting, make sure you get the serial number and manufacture date from the machine ID label. This will help us help you faster. Grizzly T...
Page 5 - Identification
Model G9717 (Mfd. Since 3/00) -3- A. Adjustable Chip Shield B. Adjustable Spark Arrestor C. Spark Shield Hinge Assembly D. Grinding Wheel Cover E. Rubber Foot F. ON/OFF Toggle Switch G. Work Rest Adjustment Slide H. Work Rest Identification Figure 1. Model G9717 identification. H C G F D A E B To re...
Page 6 - Machine Data Sheet
-4- Model G9717 (Mfd. Since 3/00) MODEL G9717 6" BENCH GRINDER Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Overall Dimensions: Height ...................................................................................................
Page 7 - For Your Own Safety, Read Instruction; NOTICE; Safety Instructions for Machinery
Model G9717 (Mfd. Since 3/00) -5- ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always dis...
Page 9 - Additional Safety for Grinders
Model G9717 (Mfd. Since 3/00) -7- Additional Safety for Grinders Serious injury or death can occur from impact injuries. Rotating grinding wheels can easily remove skin, or entanglement /amputation injuries can occur from being caught in moving parts or in-running pinch points. Flying sparks can ign...
Page 10 - SECTION 2: POWER SUPPLY; Availability
-8- Model G9717 (Mfd. Since 3/00) SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize th...
Page 12 - Needed for Setup; Unpacking
-10- Model G9717 (Mfd. Since 3/00) SECTION 3: SETUP The following are needed to complete the setup process, but are not included with your machine. Description Qty• Safety Glasses ........................................... 1 • Wrench 8mm .............................................. 1 • Wrench 14m...
Page 13 - Hardware Recognition Chart
Model G9717 (Mfd. Since 3/00) -11- 5mm Hardware Recognition Chart
Page 14 - Inventory
-12- Model G9717 (Mfd. Since 3/00) Figure 3. Inventory. A B C D E F G H I J K L M Inventory (Figure 3): Qty A. Spark Arrestors .......................................... 2 B. Phillips Head Screws M5-.8 X 8 (Arrestor) . 2 C. Lock Washers 5mm (Arrestor) ................... 2 D. Flat Washers 5mm (Arres...
Page 15 - Workbench Load; Placement Location
Model G9717 (Mfd. Since 3/00) -13- Cleanup Site Considerations Figure 4. Minimum working clearances. 8 1⁄4 " 16" The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely w...
Page 16 - Mounting; Surface Mounting; Through Mounting
-14- Model G9717 (Mfd. Since 3/00) Mounting Machine Base Workbench Lag Screw Flat Washer Glue Applied to Threads and in Hole Figure 7. Surface mount using lag screws. Popular for smaller fractional HP grinders is the . Lag screws are installed into pre-drilled holes in the table top. Sometimes glue ...
Page 17 - Assembly; Spark Deflector Adjustment
Model G9717 (Mfd. Since 3/00) -15- Assembly The spark deflector traps burning grinding slag within the grinding wheel housing to give it time extinguish and cool. As the wheel wears, the spark deflector is adjusted closer to the grinding wheel to maintain a safety gap of 1 ⁄ 8 " – 1 ⁄ 4 " (s...
Page 18 - Test Run; Power Connection; Connecting Power
-16- Model G9717 (Mfd. Since 3/00) Test Run Once the assembly is complete, test run your bench grinder to make sure it runs properly and can be put into service. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) that no major vibration exists. If, du...
Page 19 - SECTION 4: OPERATIONS; Operation Overview
Model G9717 (Mfd. Since 3/00) -17- SECTION 4: OPERATIONS To complete a typical operation, the operator does the following: 1. Examines the workpiece to make sure it is suitable for grinding. 2. Inspects, performs a "ring test", and installs the correct grinding wheel for the type of workpiec...
Page 20 - Wheel Selection
-18- Model G9717 (Mfd. Since 3/00) Some workpieces are not suitable for grinding on a bench grinder. Before grinding, inspect all workpieces for the following: • Hard Workpiece: Workpieces that are made of stone, carbide, stainless steel, ceramics, glass, or have hardened welds will wear out most ge...
Page 21 - Installation
Model G9717 (Mfd. Since 3/00) -19- Wheel Removal & Installation 6. Pull the wheel free from the spindle. There will also be a paper disc and a wheel flange on the back side of the wheel. Always make certain there is a paper or fiber disc between the wheel flanges and the wheel itself, this helps...
Page 22 - Wheel Inspection
-20- Model G9717 (Mfd. Since 3/00) Wheel Inspection Do not assume that a wheel is in sound condition just because it is new—often damage can occur in shipping, with age, or with exposure to mois-ture. Inspect every wheel for damage. First, do a Visual Inspection. Look for any cracks, chips, nicks or...
Page 23 - SECTION 5: ACCESSORIES; Basic Eye Protection
Model G9717 (Mfd. Since 3/00) -21- SECTION 5: ACCESSORIES ACCESSORIES Aluminum Oxide Grinding Wheels -Type 1 Model G7408—6" x 3 ⁄ 4 " ( 1 ⁄ 2 " Bore) 24-Grit Model G7409—6" x 3 ⁄ 4 " ( 1 ⁄ 2 " Bore) 36-Grit Model G7410—6" x 3 ⁄ 4 " ( 1 ⁄ 2 " Bore) 46-Grit Model G7...
Page 25 - SECTION 6: MAINTENANCE; Schedule
Model G9717 (Mfd. Since 3/00) -23- SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructio...
Page 26 - Troubleshooting; Grinder Operations
-24- Model G9717 (Mfd. Since 3/00) SECTION 7: SERVICE Troubleshooting Motor & Electrical Symptom Possible Cause Possible Solution Motor will not start; fuses or circuit breakers blow. 1. Switch is at fault.2. Open circuit in motor or loose connections.3. Incorrect fuses or circuit breakers in po...
Page 27 - Wiring Safety Instructions
Model G9717 (Mfd. Since 3/00) -25- SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before s...
Page 28 - Wiring Diagram
-26- Model G9717 (Mfd. Since 3/00) READ ELECTRICAL SAFETY ON PAGE 25! Wiring Diagram Ground Run Capacitor 40 MFD 250 VAC 110 VAC 5-15 Plug Bl Bk Bk Bk Wt Rd Rd Wt Gn Neutral Hot Ground G9717 Grinder Motor 110V ON/OFF Switch Gn Bk Wt Base Electrical Access Panel
Page 29 - Main Breakdown
Model G9717 (Mfd. Since 3/00) -27- 1 2 5 6 7 8 9 10 11 12 13 14 15 16 17A 19 25 26 27 29 31 32 4 34 35 36 37 40 44 45 34 34 30 36 35 36 36 17B 46 3 18 21 22 23 34 38 39 42 43 44 3 20 35 22 24 19 41 9 34 35 Main Breakdown SECTION 9: PARTS
Page 30 - Main Parts List
-28- Model G9717 (Mfd. Since 3/00) REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P9717001 WHEEL COVER LH OUTER 23 P9717023 SPINDLE NUT RH M12-1.75 X 22 2 P9717002 SPINDLE NUT LH M12-1.75 X 22 24 P9717024 WHEEL COVER RH OUTER 3 P9717003 WHEEL DISC 25 P9717025 BASE 4 P9717004 SPARK ARRESTOR 26 P9717...
Page 31 - WARRANTY CARD
C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...
