Winegard RM-EX02 - Manuals - manualsarea.com

Page 2 - Operation

Tuning Antenna STEP 1 . Your receiver should indicate it is receiving a signal. To tune your antenna for the best signal strength. SLOWLY move the antenna left, then right, until you have found the position that gives the highest signal strength. It is important to turn the antenna slowly. Because t...

Page 3 - Things you need —; Winegard’s Digital Elevation Sensor has been; The system must be level for; RW-1000 can be trimmed to fit ceiling plate.; Carefully; Center Roof Line; Assembly & Installation; currently; Antenna Reflector at 90; Signal from satellite; look angle; Trouble Shooting

4 5 Things you need — Screwdrivers (Phillips and slot) 1-3/4” hole saw 7/16” wrench ABS glue Drill with 1/8” bit Tape measure Non-hardening sealant (Check manufacturer’s specifications for compatibility with your roof material.) Winegard’s Digital Elevation Sensor has been INSTALLED and CALIBRATED a...

Page 4 - INSIDE RV; DIGITAL ELEVATION SENSOR ROOF CONNECTIONS

THREADED ROD, WASHER AND NUT FIGURE 8 INSIDE RV Special instructions: For roof thickness greater than 6-1/2”. Parts Needed: (not included) RP-4400 14” worm gear for roof 3200369 Directional handle extension2162031 Long threaded rod Instructions:STEP 8. Place nut on threaded rod. See Figure 8. STEP 9...

Page 5 - See template on reverse side.; cutting the directional handle.; CUTTING SHAFT LENGTH

See template on reverse side. STEP 15. The directional handle and threaded rod will fit roofs up to 5-1/4” thick. If you are using wedges to compensate for roof/cceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker roofs. Each exten...

Page 6 - Roof Template; DRILL THROUGH CEILING.

ALIGN WITH BASEPLATE AREA MARKED “FRONT” POINT TO FRONT OF VEHICLE  Roof Template 1/8” DRILL BIT 8 HOLES. DO NOT DRILL THROUGH CEILING. 1-3/4” DIA. DRILL COMPLETELY THROUGH CEILING 

Page 7 - INITIAL INSTALLATION; APPROXIMATELY 360° FROM; POINT TO

9 300 310 320 330 340 350 50 20 30 40 POINT NOR TH 290 10 60 70 240 250 CAUTION!After INITIAL INSTALLATION , the antenna SHOULD ROTATE APPROXIMATELY 360° FROM TRAVEL POSITION.The pointer on the DIRECTIONAL HANDLE should point towards the RED SCREW ON THE ROTATION CLAMP when in the TRAVEL POSITION. F...

Page 8 - IMPROPER WIRING WILL; Check connectors and cable entry points; properly sealed to prevent; Digital Elevation Sensor Interior Wallplate

10 11 FIGURE 17 Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days. STEP 19. See Figure 17. If using the SM-1000 surface mount box, feed cable through hole in box. STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important ...

Page 9 - Parts List

Parts List Feed Arm P.N. 2744946 46 cm Reflector (4) Flat Head Bolts Back-up Frame Pivot Bracket Pin, 1/4 x 3.25” long (Not Shown: E-clip for 1/4” Pin Travel Support LNBF LB-6000 Carriage Bolt (not shown) Flange Nut 1/4-20 Roller Hex Head Bolt 1/4-20 x 2.5” Nylock Nut 1/4-20 (not shown) Screw #10-24...

Page 11 - Specifications

ANTENNA & MOUNT Height when raised 30” vertical max. Height in the travel position 8” max. Operating radius 17” (34” diameter circle) Roof space required 26” LNB Compatible with DIRECTV ® , DISH ® , and Bell TV™ (northern U.S. and Canada) Weight 12 lbs Color Cool gray Antenna height 20.9” Antenn...