Winegard TR-6018 - Manual
Winegard TR-6018 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Parts; Assembling the Home Digital Satellite Antenna; Satellite Antenna with Tripod Kit 3; DISH Receiver Setup
- Page 3 – You are now ready to watch TV!; Satellite Location 129°W Angles; Satellite Antenna with Tripod Kit 5
- Page 4 – Once accurately; Satellite Antenna with Tripod Kit 7
- Page 5 – WINEGARD MOBILE PRODUCTS LIMITED WARRANTY; replace the product.; RETURN AUTHORIZATION POLICY; See manufacturer’s limited warranty policy.
tripod, and push
down until the
level snaps into
place. Loosen the
lock knobs on the
tripod base.
leg, and slide the leg into
the tripod base until the
leg locks into the desired
position. Repeat for all
three legs.
until the bubble rests in
the center of the bubble
level. The tripod is now
level. Tighten the lock
knobs, and remove the
bubble level.
Parts
Find a place to set
up the tripod with a
clear view of the southern
sky. Avoid obstructions
such as trees, hills, or
buildings—these can
block the signal from the
satellite.
pivot
foot
tabs
lock knob
bubble should
be in the center
3
2
4
5
1
Push in the tabs on
either side of one
Place the bubble
level on top of the
Slide legs toward or
away from the base
For extra stability,
insert the stakes
After assembling the tripod, follow the instructions to assemble the satellite antenna. If the satellite antenna is
already assembled but is being set up at a new location, follow the instructions for receiver setup. Turn to
page 3 for DISH
®
receiver setup or to page 5 for DIRECTV
®
receiver setup.
This manual provides instructions for both assembling and disassembling your tripod mount with home digital
satellite antenna. To set up your tripod mount with satellite antenna, begin with assembling the tripod. The tripod
requires only a one-time assembly and can be stored between uses. See page 7 for more information on storage
and disassembly.
into the holes on the
pivot feet of the legs, and
push the stakes into the
ground. Check that
the tripod is still
level.
tripod base
storage
bag
stakes (3)
bubble
level
legs (3)
1
2452225
TR-6018
www.winegard.com
For Technical Services, Call 1-800-788-4417
For Receivers and Programming, Call 1-866-609-9374
For up-to-date information on receiver compatibility
and programming, visit www.winegard.com/receivers
DO NOT RETURN ANTENNA TO PLACE OF PURCHASE.
Satellite Antenna with Tripod
Assembling the Tripod
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
1/4-20 x 5/8” carriage bolt (4) through the feed arm of the back-up/feed support assy. 1/4-20 hex nut (4) of the reflector with the four holes on the back- up/feed support assy. bolts through the four holes on the front of the reflector. Thread a 1/4-20 hex nut onto each bolt. Parts Assembling the H...
Elevation Loosen the elevation bolts on either side of the back-up/feed support assy. Raise the dish to the specified elevation angle that you found in step 8 of the receiver setup. The red line on the back-up/feed support assy., shown next to the elevation bolt, should line up with the correct angl...
Elevation Loosen the elevation bolts on either side of the back-up/feed support assy. Raise the dish to the specified elevation angle that you found in step 8 of the receiver setup. The red line on the back-up/feed support assy., shown next to the elevation bolt, should line up with the correct angl...
