Winegard RS-2000 - Manual
Winegard RS-2000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – NOTE: Holes for mounting brackets are at corners of; The power supply/wall outlet assembly may be; ANTENNA MOUNTING INSTRUCTIONS
- Page 3 – Install connectors on downlead and set 2 cable; FIGURE 7; This unit is equipped with a; Install terminals on wires from +12 VDC source
- Page 4 – HOW YOUR; WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY; TO TEST SYSTEM
ROADSTAR
RV AND VAN TV ANTENNA
MODELS RS-2000 & RS-3460/RS3460B
Made in U.S.A.
INSTRUCTIONS
Winegard Company
3000 Kirkwood St., Burlington, IA 52601-2000
Printed in U.S.A. 2451806 © Winegard Company, 1998, 2004, 2006 Rev.3 10/10
SPECIFICATIONS
Bandpass
VHF/FM ..............................
54 to 216 MHz
UHF ....................................
470 to 810 MHz
Amplifier Gain ......................
VHF* ..................................
15.5 dB avg.
UHF ....................................
19.5 dB avg.
Impedance ............................
75 ohm unbalanced
Response ..............................
.25 dB per 6 MHz
VSWR ....................................
1.8:1 max.
Power Required ....................
+12 VDC at 85 ma
Weatherproof Housing .........
Weatherable
UV stabilized
copolymer
WINEGARD
®
*Has fixed FM trap to reduce interference.
DESCRIPTION
Winegard's RoadStar
TM
omnidirectional antenna provides
excellent reception of VHF/UHF TV channels. The
RoadStar compact modern styling is unobtrusive and
blends well with the designs of recreational vehicles. The
UV stabilized copolymer housing makes the antenna
virtually impervious to weathering and color change.
The unique omnidirectional characteristics provide ex-
cellent reception in areas where stations are in different
directions without the need for a complex rotor system.
A built-in amplifier provides up to 6 times the received
signal on VHF and 9 times the UHF signal insuring the
best possible reception in color and black and white.
The RS-2000 package includes antenna, +12 VDC power
supply with two-way splitter, 30' downlead cable, 6' TV set
cord, hardware and mounting bracket.
PARTS LIST (RS-2000) White Housing
1
Amplified Antenna
2120415
6
10-32 Hex Nut, Nylock
2160216
1
Power Supply with Hardware
2120123
1
30' Coaxial Cable
2753015
1
6' Coaxial Cable
2753752
3
Roof Mounting Brackets
3720303
6
#10 x 1" Thread Cutting Screws
2160178
1
Bolt, 1-14 x 1" Nylon
3200350
1
Mounting Plate
3710248
6
10-32 x 5/8" Bolt
2160173
6
Washer, #10 Aluminum
1140302
PARTS LIST (RS-3460) White Housing
(RS3460B) Black Housing
1
Amplified Antenna (white)
2120415
Amplified Antenna (black)
2120404
6
10-32 Hex Nut, Nylock
2160216
3
Roof Mounting Brackets
3720303
6
#10 x 1" Thread Cutting Screws
2160178
1
Bolt, 1-14 x 1" Nylon
3200350
1
Mounting Plate
3710248
1
Coaxial Cable Boot
3200154
6
10-32 x 5/8" Bolt
2160173
6
Washer, #10 Aluminum
1140302
T M
CLEANING ANTENNA HOUSING
The surface of the antenna is a tough laminated
ultraviolet shield. Clean only with mild soap and
water.
Use no solvents, alcohol, or cleaning
fluids.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 FIGURE 1 STEP 2. Place assembled mount on bottom of antenna housing and thread in 1" nylon bolt. Spin the assembledmount to tighten securely. STEP 3. Attach end of coaxial downlead cable with boot to jack on bottom of antenna and slide boot up over bootcollar. See Figure 3. FIGURE 2 FIGURE 4 S...
3 STEP 7. Install connectors on downlead and set 2 cable as shown on page 4. Attach antenna downlead cable tojack on power supply marked “ANT”. See Figure 7. FIGURE 7 FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11 CHECKING POWER SUPPLY OPERATION (Power Supply not supplied with RS-3460) 1. Tune TV receiver to...
4 WARNING DO NOT INSTALL COUPLERS, SPLITTERS, ETC.BETWEEN THE POWER SUPPLY AND THE AN-TENNA. INSTALLATION OF ANY ITEM ON THE DOWN-LEAD MAY CAUSE A SHORT IN THE SYSTEM. THEDOWNLEAD SUPPLIES +12 VDC TO THE PREAMP INTHE ANTENNA. HOW YOUR SYSTEM WORKS Turning power supply on sends +12 VDC up cable toant...
