Winegard CC-7870 - Manual

Winegard CC-7870

Winegard CC-7870 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
Page: / 1
Loading the manual

67 CHANNEL

2-WAY ANTENNA

TV SET COUPLER

Model CC-7870

(75 ohm)

Made in U.S.A.

Winegard Company

3000 Kirkwood St., Burlington, IA. 52601

INSTRUCTIONS

CONSUMER 90 DAY WARRANTY

The Winegard Company warrants this Winegard product against any

defects in materials or workmanship within 90 (ninety) days from date of

purchase. No warranty claim will be honored unless at the time the claim is

made, you present proof of purchase to an authorized Winegard dealer (if

unknown, please contact Winegard Company, 3000 Kirkwood Street,

Burlington, IA 52601-2000, Telephone 800-288-8094).

Winegard Company (at its option) will either repair or replace the

defective product at no charge to you. This warranty covers parts, but

does not cover any costs incurred in removal, shipping or reinstalla-

tion of the product. The warranty does not extend to products which

have been subjected to misuse, improper installation, or to damage

caused by wind, lightning, ice or other occurrences over which the

manufacturer has no control.

The 90 Day Warranty is provided on the condition that the

equipment is properly delivered with all handling and freight charges

prepaid to your Winegard dealer for return to our factory for repair or

replacement. Winegard dealers will arrange for the replacement or

repair and return to you without charge the product which failed due

to defective material or workmanship.

WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES

FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE

BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR

ST

AT

UT

OR

Y

IN

CL

UD

IN

G

WA

RR

AN

TIE

S

OF

F

IT

NE

SS

F

OR

A

PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED

TO THE 90-DAY PERIOD OF THIS WARRANTY.

The foregoing shall be the sole and exclusive remedy of any

person, whether in contract, tort or otherwise, and Winegard shall not

be liable for incidental or consequential damage or commerical loss,

or from any other loss or damage except as set forth above.

Some states do not allow limitations on how long an implied

warranty lasts, or the exclusion of limitation of incidental or conse-

quential damages, so the above limitations or exclusions may not

apply to you.

This warranty gives you specific legal rights and you may also have

other rights

which vary

from state

to state.

Rev 2/08.

The CC-7870 couples two 75 ohm leads from
any two antennas to a 75 ohm downlead. Input
and output are thru standard 75 ohm F-jacks.
AC-DC passive input to Set 1 side. Three FC-
5910 connectors provided. -3.5 insertion loss.

INSTRUCTIONS

DESCRIPTION FOR

COUPLING TWO ANTENNAS

STEP 1. Install FC-5910 connectors on coax
cables per instructions on back of sheet.

STEP 2. Attach antenna downlead to jack
marked "Antenna" and antenna cables to jacks
marked "Set 1" and "Set 2". See illustration.

STEP 3. Mount coupler with screws and bracket
as shown.

WAYS TO MOUNT COUPLER

Printed in U.S.A. 2451860 Rev. 3/97

INSTALLING FC-5910

CONNECTORS ON COAX CABLE

STEP 1: Strip outer cover back 1/2"* from end of

cable. Fray braid back as far as outer cover will allow.

STEP 2: Trim braid close to outer cover and remove

1/4"* of inner insulation being careful not to nick

center conductor. Make sure no foil or braid can

touch center conductor.

STEP 3: Slide connector tip between braid and inner

insulation (braid and foil, on foil shield cable) and push

connector on cable as far as it will go. Crimp built-in

ferrule with proper crimping tool. Hex connector

requires hex crimping tool. Do Not crush cable out-

of-round.

* If installing in very hot weather, increase these dimensions 1/8".

DESCRIPTION FOR SPLITTING A SINGLE

COAX LINE FOR SECOND TV HOOK-UP

INSTRUCTIONS

STEP 1. Install FC-5910 connectors on coax
cables per instructions on back of sheet.

STEP 2. Attach antenna downlead to jack
marked "Antenna" and antenna cables to jacks
marked "Set 1" and "Set 2".

STEP 3. Mount coupler with screws and bracket
as shown.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Winegard Models

All Winegard Other