Page 2 - Part Number; Installation; Copper and fiber ports
2 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 PWR LKF 100Base-FX 10/100Base-TX TX RX RS-232 4 3 2 1 LNK LNK LNK LNK AIS AIS AIS AIS fiber port Ethernet port RS-232 port T1/E1 ports Part Number Fiber-Optic - Single Fiber, Single Mode, 100Base-FX S4TEF1029-...
Page 3 - Switch set #2 - serial and ethernet options
4 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Switch set #1 - T1/E1 options 5, 6, 7, 8 - Loop-Back settings The loop-back setting is used for installation and network debugging procedures. Eachof the T1/E1 ports can be individual...
Page 4 - Installation — Continued
6 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation — Continued Switch set #2 - serial and ethernet options 6 - Twisted-pair Auto-Negotiation Up (Enabled) - The media converter “advertises” ALL rate and mode capabilities to the network: • 100 Mb/s ...
Page 5 - Hardware/software jumper; Install the T1/E1 cable; Install the fiber cable
8 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation — Continued Hardware/software jumper The jumper is located on the circuit board, inside the mediaconverter housing. Hardware: The media converter mode is determined by the switchsetting (see pages...
Page 6 - Install the RS-232 data cable; Operation; Fiber network LEDs; LKF; Optional accessories; Ethernet LEDs
10 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Install the RS-232 data cable (included) 1. Use the enclosed RS-232 data cable with a male, DIN 6-pin connector on oneend and a DB-9 connector installed on the other end. 2. Connect ...
Page 7 - Accessing the local RS232 factory maintenance interface; Operation — Continued; Remote management function; SNMP
13 [email protected] -- Click the “Transition Now” link for a live Web chat. Operation -- Continued Accessing the local RS232 factory maintenance interface 1. Make sure that this Device is configured for accessing the maintenanceinterface via the RS232 port (Switch #10, on Bank #1, down. Se...
Page 10 - Cable Specifications; Fiber cable
18 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Operation -- continued To Reset the local device: Caution: This command will interrupt T1/E1 and Ethernet traffic. It will takeseveral seconds to restore the data path. Failure to observe this caution might c...
Page 11 - Ethernet cable
20 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Cable Specifications -- Continued The fiber optic transmitters on this device meet Class 1 Laser safety requirements perIEC-825/CDRH standards and complies with 21 CFR1040.10 and 21 CFR1040.11. Ethernet cable...
Page 12 - Cable Specifications —Continued; Technical Specifications
22 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Cable Specifications —Continued RS-232 cable (included with the media converter) Connectors Gauge: 6-pin DIN and DB-9 / 24-22 AWG Attenuation: 20 dB/1000 ft. @ 10 MHz Differential characteristic impedance: 10...
Page 13 - Troubleshooting
24 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Troubleshooting If the media converter fails, isolate and correct the failure by determining the answersto the following questions and then taking the indicated action: 1. Is the “PWR” LED illuminated?NO• Ens...
Page 14 - Contact Us; Declaration of Conformity; Compliance Information; Canadian regulations
26 S4TEF10xx-11x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Contact Us Technical support Technical support is available 24 hours a day.US and Canada: 1-800-260-1312 International: 00-1-952-941-7600 Transition now Chat live via the Web with Transition Networks Technica...