Smart 2000i - Manuals - manualsarea.com

Page 3 - Contents

99-00496-00 Rev A0 Contents Replacing the Projector in a 2000i ................................................... 1Aligning the Projected Image ........................................................... 6Customer Support........................................................................... 11...

Page 5 - Projector Replacement Guide for the 2000i; Replacing the Projector in a 2000i; Rear; To remove the original projector; Shut down the computer, and then press and hold the; Projector Standby; button on the; Toggle the projector’s power switch to the off position.; secures the projector to the projector plate.

99-00496-00 REV A0 Projector Replacement Guide for the 2000i 1 Replacing the Projector in a 2000i Use these instructions to install a replacement NEC MT860 or NEC MT1060 projector in your Rear Projection SMART Board 2000i interactive whiteboard. To remove the original projector 1. Shut down the comp...

Page 6 - CAUTION; Be

2 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 5. With another person supporting the projector, reach through the view port and remove the three nuts (including the steel and nylon washers) that secure the projector in place and thenremove the projector. Use the provided 7/16" nu...

Page 9 - Align the projected image as described in the next section.

99-00496-00 REV A0 Projector Replacement Guide for the 2000i 5 9. Connect the video, power and serial cables to the projector, along with any other cables (VCR, external monitor, etc.) that you removed in step 2. 10. Replace the strap that secures the projector to the projector plate. 11. Plug the p...

Page 10 - Aligning the Projected Image; To adjust image roll

6 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 Aligning the Projected Image If the projected image is blurry or does not fit the screen, complete the four adjustment procedures thatfollow. For the first three, (roll, side-to-side and image size adjustment), you must watch the image o...

Page 11 - To adjust the image laterally

99-00496-00 REV A0 Projector Replacement Guide for the 2000i 7 To adjust the image laterally 1. Crouch behind the projector and look at the projected image through the view port. 2. Using the supplied 7/16" nut driver, loosen the two nuts on the left side of the projector plate. 3. Slide the pro...

Page 12 - To change the image size; NOTE

8 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To change the image size 1. Crouch behind the projector and look at the projected image through the view port. 2. Loosen the four hex screws that secure the projector to the projector plate using the provided 3 mm hex key. NOTE : These s...

Page 13 - Slide the projector backward or forward to alter the image size.

99-00496-00 REV A0 Projector Replacement Guide for the 2000i 9 Screen Removed for Clarity As you maneuver the hex key through the access holes, watch it from the side to seewhen it engages with the hex screw. Look here to see when the hex key engages with the screw 4. Slide the projector backward or...

Page 14 - To move the image up or down; right side of the Electronics Tray.; Remove the plastic cap to reveal an access hole.

10 Projector Replacement Guide for the 2000i 99-00496-00 REV A0 To move the image up or down 1. Crouch down in front of the screen. 2. Look underneath the pen tray and locate the Electronics Tray. Locate a plastic cap on the right side of the Electronics Tray. Electronics Tray 3. Remove the plastic ...

Page 15 - Customer Support; Rear Projection; Contacting SMART Technical Support; Main switchboard; 1th Avenue SW; Product Warranty; Warranty Shipping Charges

99-00496-00 REV A0 Projector Replacement Guide for the 2000i 11 Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact yourlocal reseller first if you experience problems with any SMART product. SMART’s resellers canreadily provide you with quick advice ...