SIIG 04-0835A - Manuals - manualsarea.com

Page 2 - System Requirements; Desktop PC with an available PCIe slot; Package Contents; Spare low profile bracket

2 System Requirements • Desktop PC with an available PCIe slot • Windows ® 8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / Server 2008 R2 Package Contents • DP Wireless-N PCI Express Wi-Fi Adapter • Spare low profile bracket • Antennas (...

Page 3 - Layout; transmitting or receiving data.

3 Layout Figure 1: CN-WR0811-S1 Layout Status LED• Lnk/Act on: Indicates valid connection. • Lnk/Act quickly flashing: The adapter is transmitting or receiving data. Status LED Anttennas

Page 4 - Hardware Installation; Note

4 Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your c o m p u t e r ’ s r e f e r e n c e m a n u a l f o r f u r t h e r information, if needed.Static Electricity Discharge may permanently d...

Page 5 - Software Installation

5 4 . To install the card, carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 5 . Replace the slot bracket's holding screw to secure the card. 6 . Replace the computer cover and reconnect the power...

Page 6 - Click Install then click Close, and Wireless; Check the; Wireless LAN Service; click; Next

6 Figure 2 4 . Click Install then click Close, and Wireless LAN Service is installed successfully. Figure 3 3 . Check the Wireless LAN Service , then click Next .

Page 7 - Driver Installation

7 Driver Installation Follow the instructions below to install the driver.1 . Install the board and boot up Windows. 2 . At the Found New Hardware, click Cancel. Skip this step if not prompted. 3 . Insert the driver CD. At the prompted CD driver window, select folder PCIe , then double click Setup ....

Page 8 - To Verify Windows Installation; For Windows Vista; Wireless Network Configuration

8 To Verify Windows Installation 1 . Go to Device Manager to verify installation. For Window 8 / Windows 7 / Windows XP / Server 2003 / 2008 R2 : Right click Computer or My Computer , click Manage , then click Device Manager . For Windows Vista : Right click Computer , click Manage , click Continue ...

Page 9 - View Available Wireless Networks

9 Right click the RaUI icon in the taskbar, then select Use Zero Configuration as Configuration Utility to configure by WZC, or select Use RaConfig as Configuration Utility to configure by RaUI. For Window 8, Windows 7, Vista, WZC and RaUI can be used together and no need to do the selection. Figure...

Page 10 - For advanced settings, click; Change advanced; select tab; Wireless Networks; At the Wireless Network Connection, double; Connect

1 0 Figure 6 Click Continue Anyway For advanced settings, click Change advanced settings , select tab Wireless Networks , then click Properties (as Figure 7 & 8). At the Wireless Network Connection, double click the preferred wireless network, enter the Network key, click Connect , then click Co...

Page 12 - OK; to save the settings.

1 2 Select the type of Network Authentication and Data Encryption, click OK to save the settings. Figure 9

Page 13 - Ralink UI

1 3 Ralink UI Note : If you configured your wireless network using WZC utility on page 9, this utility is not needed.Double click the Ralink icon in the task bar. Click the icon to bring up the AP list. Figure 10 Click the icon to bring up the network AP list Double click the the preferred AP from t...

Page 15 - Technical Support and Warranty

1 5 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit...