SIIG 04-0600A - Manuals - manualsarea.com

Page 2 - Package Contents; Mounting hardware; Mounting Hardware; M6x20mm Machine Screw

2 Package Contents • (2) Speaker mounts • (2) 1-hole adapters • (2) 2/4-hole adapters • (2) 2 ¼” ceiling mount extensions • Mounting hardware • Quick installation guide Mounting Hardware M6x20mm Machine Screw M5 x 20mm Machine Screw 8-32 x 5/8" Machine Screw 1/4"-20 x 1/2" Machine Screw ...

Page 3 - Installation; Single Hole Mounting; Figure 1

3 Installation Please read the instructions prior to installation. Thisspeaker mount is designed solely for the mounting ofsmall speakers weighing less than 8lbs. We are notresponsible for damage that may occur if speakersweighing more than 8lbs. are used. The user will have to determine which type ...

Page 4 - Figure 3

4 2. Once the proper configuration is determined, secure the post to the speaker. 3. Some speakers use the smaller M4 x 8 screw, which is inserted into the off-center on the mounting post,see Figure 2 below. 4. Check the size of the hole, make sure you have the 5/8"-32 x 5/8" machine screw, ...

Page 5 - Key Hole Mounting; below. Be sure the key hole nut is installed; Figure 4

5 5. When the correct size is determined, place thescrew through the speaker post and attach to therear of the speaker enclosure. If the screw does nottighten properly, use the M5 x 1/8" plastic washerto tighten it up. Key Hole Mounting 1. If your speaker has a factory key hole design, youwill u...

Page 7 - Figure 5

7 1/4"-20 x 1/2" Machine Screw 4-Hole Orientation 2-Hole Orientation Figure 5 Back Speaker Self-Tapped Mounting 1. Locate the optimum location for the mountingplate and use it as template to mark the drillinglocations. Do not drill or screw into the speakerwhere you could possibly damage the...

Page 8 - Figure 6; Mounting to the Wall or Ceiling; Using a stud finder, locate the wood stud or framing

8 Back Speaker ST5.5 x 19 Self Tapping Screw Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surfaceapplications is supplied. You will need to determine whatstyle hardware will work best with your mounting surface.Always use caution when drilling into a wall or...

Page 9 - Figure 7; Drill holes through the drywall and into the wood; Drywall Surfaces; Locate the best mounting location in the ceiling or

9 ST5.5 c 45 Self Tapping Screw Figure 7 3. Drill holes through the drywall and into the wood stud using a 1/8" drill bit. These holes should bedrilled 1-7/8" deep, see Figure 7 above. 4. After the holes are drilled, mount the wall plate using the self tapping screws. Drywall Surfaces 1. Loc...

Page 10 - Figure 8; Concrete Surface; Using the wall plate as a template, mark hole

1 0 4. With the anchors in place, mount the wall platesusing the ST5.5 x 45 self tapping screws, seeFigure 8 below. Figure 8 ST5.5 x 45 Self Tapping Screw Insert screw through wall plate and into the alligator anchor Insert Alligator Anchor Pre Drill 5/16" Holes Concrete Surface 1. Using the wal...

Page 11 - Figure 9; Extension Mounting

1 1 Figure 9 Insert Alligator Anchor ST5.5 x 45 Self Tapping Screw Using the hammer to tap anchor into place Insert screw through wall plate and into the alligator anchor 3. With the wall anchor in place, mount the wall plateusing the ST5.5 x 45 self tapping screws, seeFigure 9 above. Extension Moun...

Page 12 - Speaker Mounting

1 2 Low-Profile Mounting This is for wall and ceiling application. 1. Install the low-profile portion of the speaker mount to the wall plate or 2-1/2" extension. 2. Secure the setscrew to hold the extension in place with the weight of the speaker attached. Tighten the allen screw using the provi...

Page 13 - Blank Page

Page 15 - Technical Support and Warranty; s Online Support has answers! Simply visit our web site at

1 5 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a fewclicks away. You can also submit q...

Page 16 - PRODUCT NAME; FCC COMPLIANCE STATEMENT:

About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/Oconnectivity products, including PCI & ISA serial and parallel ports, USB, SerialATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards,and other accessories. SIIG is the premier on...