SIIG 04-0322B - Manuals - manualsarea.com

Page 2 - Package Contents; (1) Dual connector Serial ATA power cable; Board Layout; Hardware Installation; Turn OFF the power to your computer and any

2 Package Contents • (1) Serial ATA 4-Channel PCI board • (1) Driver CD • (2) Serial ATA cable • (1) Dual connector Serial ATA power cable • This quick installation guide Board Layout S e r i a l A T A C o n n e c t o r s C N 4 C N 3 C N 2 C N 1 Hard Disk LED Pins Figure 1. Serial ATA 4-Channel PCI ...

Page 3 - Device Connection

3 • Remove your computer’s cover and install the card in an available PCI slot. • Push the board down firmly, but gently, until it is well seated. Install a slot bracket holding screw tosecure the card. • Now go to Device Connection to connect your Serial ATA hard disk drive(s). Device Connection If...

Page 4 - Note; : If you like to monitor disk activity of the; figure 1; Software Installation; Windows 98/98SE Driver Installation; and click Properties. Select Device

4 Note : If you like to monitor disk activity of the Serial ATA hard drives, you may at this time connectthe hard disk LED of the system case to the HardDisk LED Pins on the Serial ATA controller, see figure 1 , on page 2 for the location of the pins. For most systems connect the red wire to the pin...

Page 5 - Insert the driver CD and click Next.; Install the board and boot up Windows 98.; At the Add New Hardware Wizard, click Next.; Windows ME Driver Installation; Manager

5 5. Insert the driver CD and click Next. 6. Select Search for a better driver ... and click Next. 7. Check CD-ROM drive, uncheck the other boxes,then click Next. Click Next again, then Finish. 8. Click Yes to restart Windows to complete the driverinstallation. For Existing Windows 98 Installation1....

Page 7 - Verify Proper Installation for Windows NT4.0; Adapters

7 2. At the Windows NT Setup screen, press F6 to specify and add the driver. 3. Press S, select Other, then press Enter. 4. Insert the driver diskette and press Enter. 5. Select Silicon Image SiI 3114 ... Controller for Windows NT 4.0 and 2000 , and press Enter. 6. Press Enter to continue and follow...

Page 8 - Windows 2000 Driver Installation; thoroughly tested in Windows for stability.

8 Windows 2000 Driver Installation A new installation of Windows 2000 requires a floppydisk for the driver installation. To make this floppy disk,copy the contents of the Floppy folder, found on thedriver CD, onto a blank floppy disk then follow thedirections below. For New Windows 2000 Installation...

Page 9 - Windows XP/Server 2003 Driver Installation

9 Windows XP/Server 2003 Driver Installation A new installation of Windows XP/Server 2003 requiresa floppy disk for the driver installation. To make thisfloppy disk, copy the contents of the Floppy folder,found on the driver CD, onto a blank floppy disk thenfollow the directions below. For New Windo...

Page 10 - Bios Configuration

10 Note : If a warning message pops up, click Continue Anyway , then click Finish. Our driver has been thoroughly tested in Windows for stability. 4. Remove the driver CD and restart Windows to complete the driver installation. Verify Proper Installation for Windows 2000/XP/Server 2003 1. Right clic...

Page 11 - Technical Support and Warranty; S I I G ’ s O n l i n e S u p p o r t h a s a n s w e r s !

11 Technical Support and Warranty Q U E S T I O N S ? S I I G ’ s O n l i n e S u p p o r t h a s a n s w e r s ! Simply visit our website at www.siig.com and click on Support.Our online support database is updated daily with new driversand solutions. Answers to your questions could be just a few cl...