Neff D86E34N0 - Manuals

5 Before using for the first time Safety instructions Do not flambé food directly under the extractor hood. Risk of grease filter catching fire due ! to flames. The hotplates must always be covered with a utensil. Restrictions apply to the use of the extractor hood over a solid-fuel burner(coal, woo...

6 Operating procedure The most effective method of removing vapours produced during cooking is to: ❑ Switch the ventilator ON as soon as you begin cooking. ❑ Switch the ventilator OFF a few minutes after you have finishedcooking. Setting the required fan speed: ❑ Press the corresponding button. Ligh...

7 Filters and maintenance Grease filters: Metal filters are used to trap the greasyelement of the vapours that developduring cooking. The filter mats are made from non-combustible metal. Caution: As the filter becomes more and more saturated with grease, not only does therisk of it catching fire inc...

8 Filters and maintenance Activated carbon filter: For neutralizing odours in recirculatingmode. Caution: As the filter becomes more and more saturated with grease, there is an increasedrisk of fire and the function of the extractorhood may be impaired. Important: Change the activated carbon filter ...

9 Cleaning and care Isolate the extractor hood by pulling outthe mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agentswhich contain sand, soda, acid or chlorine! ❑ Clean the extractor hood with a hot soapsolution or a mild window cleaner....

10 Replacing the light bulbs Bulbs: 1. Switch off the extractor hood and pullout the mains plug or switch off the electricity supply at the fuse box. 2. Remove the grease filters (see Filters andMaintenance). 3. Detach the bulb cover. 4. Replace the bulb (commercially availablehalogen bulb 230 volt,...

12 Prior to installation Exhaust-air mode The exhaust air is discharged upwardsthrough a ventilation shaft or directlythrough the outside wall into the open. D Exhaust air should neither be directed into a smoke or exhaust flue that iscurrently used for other purposes, nor intoa shaft that is used f...

13 For optimum extractor hood efficiency: ❑ Short, smooth air exhaust pipe. ❑ As few bends in the pipe as possible. ❑ Diameter of pipe to be as large aspossible and no tight bends in pipe. If long, rough exhaust-air pipes,many pipe bends or smaller pipe diameters are used, the air extractionrate wil...

14 Prior to installation Preparing t h e w a l l ❑ The wall must be flat and perpendicular. ❑ Make sure that the wall can bear theapplied loads. ❑ The provided screws and wall plugs aresuitable for solid masonry. On all otherwall types (e.g. plasterboard, porousconcrete, Poroton bricks) use theappro...

15 Installation preparations 5. Screw on the fixing bracket for the flueduct. 6. Screw in the 2 middle screws as aninstallation aid, leaving them projectingby approx. 5 mm. 5 0 This extractor hood is intended to be mounted onto the kitchen wall. 1. Remove the grease filter (refer to Operating Instru...

16 Installation 7. Remove the protective film from theextractor hood. Attach the extractor hood, align andscrew tightly into place. 8. Connect up the air outlet pipe. 9. Connect the hood to the electricitysupply. 10. Put on the enclosed protective cardboard for the glass plate. 11. Put on the glass ...

17 Installing the flue ducts 4. Place flue ducts on the extractor hood,push the inner flue duct upwards andattach the left and right sides to thefixing bracket. 1. Separate the flue ducts by removing theadhesive tape. 2. Remove the protective film from the twoflue ducts. Avoid damage to the sensitiv...