Jet 714000 - Manuals - manualsarea.com

Page 2 - WARNING – To reduce risk of injury:

1.0 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious...

Page 3 - SAVE THESE INSTRUCTIONS; About this manual

3 25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 26. Use recommended accessories; improper accessories may be hazardous. 27. Maintain tools with care. Keep ...

Page 4 - Table of contents; Section

4 3.0 Table of contents Section Page 1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2 2.0 About this manual ......................................................................................................

Page 5 - Features; Specifications

5 4.0 Features Figure 1 5.0 Specifications Model Number .............................................................................................................................................. JWB-10 Stock Number ....................................................................................

Page 6 - Unpacking; Contents of shipping container; Tools required for assembly

6 6.0 Unpacking Read and understand all assembly instructions before attempting assembly. Failure to comply may cause serious injury. Remove all contents from shipping carton. Do not discard carton or packing material until band saw is assembled and running satisfactorily. Compare contents of carton...

Page 7 - Assembly; Stand assembly; Table installation

7 Figure 4 7.0 Assembly 7.1 Stand assembly 1. Refer to Figure 4 to assemble stand. Use carriage bolts (HP3) and flange nuts (HP9) throughout. Only hand-tighten all fasteners at this time. 2. Make sure the two short support plates with extra holes (M) are opposite one another as shown. 3. Slip rubber...

Page 8 - Guide rail and fence; Installation; Quick-tension handle; Electrical connections; GROUNDING INSTRUCTIONS

8 7.4 Guide rail and fence 7.4.1 Installation 1. Attach guide rail (E, Figure 6) to front of table. Secure with four wing screws (HP4) and flat washers (HP5). Figure 6 Refer to Figure 7: 2. Place fence assembly (D, Figure 7) onto table at the miter slot. The rear hook should engage the rear of the t...

Page 9 - Extension cords; Adjustments; Tilting table

9 installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. T...

Page 10 - 0o Table Stop Adjustment; Adjusting table stop; Changing blades

10 NOTE: Lock handle (A, Figure 9) is adjustable – pull down on handle and rotate on pin. Release handle, making sure it settles back onto pin. Figure 10 9.2 90º Table Stop Adjustment 9.2.1 Adjusting table stop Refer to Figures 9 and 10. The table stop (C, Figure 9) is typically set to stop the tabl...

Page 11 - Adjusting blade tension; Adjusting blade tracking; Upper blade guide positioning

11 9.4 Adjusting blade tension Refer to Figure 12: The blade tension knob (P) is used to adjust blade tension. The quick tension lever (Q) must be engaged (moved to the left) before making tension adjustments with knob (P). All bearings on upper and lower guides must be clear of blade (see sect. 9.7...

Page 12 - Thrust bearing adjustment; Guide bearing adjustment; Miter gauge adjustment

12 There are two blade guide assemblies – an upper assembly (Figure 14) and lower assembly (Figure 15). Adjustments are performed in the same manner for each assembly. Each assembly must be adjusted in turn using the adjustment procedures outlined below. 9.7.1 Thrust bearing adjustment Disconnect ma...

Page 13 - Operating controls; Replacing drive belt

13 Place miter gauge into table slot and use a square to verify that 90-degree setting on scale is 90-degrees to slot. Adjust pointer (K) if necessary. Figure 16 10.0 Operating controls On/Off Switch – located on front of machine: pull switch out to start; push switch in to stop. W hen yellow safety...

Page 15 - JWB-10 Band Saw – Exploded View

Page 16 - JWB-10 Stand Assembly – Exploded View

Page 17 - JWB-10 Band Saw and Stand – Parts List; Index No Part No

17 14.1.3 JWB-10 Band Saw and Stand – Parts List Index No Part No Description Size Qty 1 ................ TS-1503041 .............. Socket Head Cap Screw.......................................... M6x16 ........................... 2 2 ................ JWB10-002 ............... Spacer ...................

Page 20 - Electrical Connections for JWB-10 Band Saw

20 15.0 Electrical Connections for JWB-10 Band Saw 1/2HP, 1PH, 115V

Page 21 - Warranty and service

21 1 6 .0 Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time p...