Jet 414471 - User Manual - manualsarea.com

Page 2 - Warranty and Service

2 1.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time perio...

Page 3 - Table of contents; Section

3 2.0 Table of contents Section Page 1.0 Warranty and Service ..................................................................................................................................... 2 2.0 Table of contents .................................................................................

Page 4 - IMPORTANT SAFETY INSTRUCTIONS

4 3.0 IMPORTANT SAFETY INSTRUCTIONS 1. Read and understand the entire instruction manual before attempting assembly or operation. 2. All JET band saws are designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a...

Page 5 - Specifications

5 4.0 Specifications Model Number ............................................................................................................................. HBS-1321W Stock Number ........................................................................................................................

Page 6 - Assembly

6 5.0 Uncrating and cleanup 1. Read and understand the entire manual before attempting setup or operation. 2. Finish uncrating the saw and inspect for damage. If any damage has occurred, contact your local distributor. 3. Remove all bolts attaching machine to shipping base. 4. Leave packing material...

Page 7 - Prior to operation; Adjusting vise square to blade

7 8.0 Electrical connections All electrical connections must be made by a qualified electrician. Failure to comply may result in serious injury. Disconnect machine from power source before changing any voltage components. Failure to comply may result in serious injury. The HBS-1321W band saw is rate...

Page 9 - Changing blades; Blade guide adjustment; Bearing guides

9 Material chips or shavings are the best indicator of proper speed and downfeed. The ideal chip is thin, tightly curled, and warm to the touch. Chips that range from golden brown to black indicate excessive force. Blue chips indicate extreme heat from too high a band speed, which will shorten blade...

Page 10 - Stationary guides; Blade tracking adjustment; Maintenance; Lubrication and gearbox

10 Figure 10 11.9.2 Stationary guides The stationary blade guides come pre-adjusted from the factory. If adjustment is needed, follow the below steps. Refer to Figure 11 . 1. Disconnect machine from power source. 2. Adjust spring loaded blade guide (A, Figure 11) by loosening or tightening the guide...

Page 11 - Hydraulic pump

11 To change gear box lubricant: 1. Disconnect machine from power source. 2. Remove drain plug and allow lubricant to drain completely. The drain plug is located on lower front of gear case under right wheel cover. Remove drain plug with a hex wrench. 3. Reinstall drain plug. 4. Remove filler cap an...

Page 12 - Replacement parts

12 13.0 Replacement parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to ser...

Page 13 - HBS-1321W – Bed and Base Assembly – Exploded View

13 13.1.1 HBS-1321W – Bed and Base Assembly – Exploded View

Page 14 - HBS-1321W – Bed and Base Assembly – Parts List; Index No Part No

14 13.1.2 HBS-1321W – Bed and Base Assembly – Parts List Index No Part No Description Size Qty 1 ............... 1321W-01G .............. Base ..................................................................... .................................... 1 2 ............... TS-1492061 ............. Hex C...

Page 17 - HBS-1321W – Arm Assembly – Exploded View

Page 18 - HBS-1321W – Arm Assembly – Parts List

18 13.2.2 HBS-1321W – Arm Assembly – Parts List Index No Part No Description Size Qty 8-1 ............. 1321W-08-1 .............. Hose Fitting ............................................................. ...................................... 2 8-2 ............. 1321W-08-2 .............. Hose Clamp...

Page 22 - Electrical Connections – HBS-1321W

Page 23 - Wiring Diagram Symbol Glossary; Symbol

23 14.1 Wiring Diagram Symbol Glossary Symbol Description Part Number LS1 Cut off Limit Switch 1321W-45 LS2 Roller Limit Switch 1321W-45-1 SB1 Emergency Switch 1321W-156 SB2 Start Switch 1321W-154 SB3 Arm Down Switch 1321W-158 SB4 Arm Up Switch 1321W-157 SB5 Stop Switch 1321W-155 HL Power Indicator ...

Jet 414471 - User Manual

Table of Contents:

Summary

Other Jet Band Saws Models