Jet 414468 - User Manual - manualsarea.com

Page 2 - Warranty and Service

2 1.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time per...

Page 3 - Table of Contents

3 2.0 Table of Contents 1.0 Warranty and Service ..................................................................................................................................... 2 2.0 Table of Contents ............................................................................................

Page 4 - Safety warnings

4 3.0 Safety warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they...

Page 5 - Introduction

5 23. Keep visitors a safe distance from the work area. Keep children away. 24. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 25. Maintain a balanced stance at all times so that you do not fall o...

Page 6 - Specifications

6 5.0 Specifications Model Number ................................................................... HBS-916W ............................................... HBS-1018W Stock Number ......................................................................... 414468 ......................................

Page 7 - Assembly

7 6.0 Uncrating and cleanup Note: Read and understand the entire manual before attempting setup or operation. 1. Finish uncrating the saw and inspect for damage. Should any have occurred, contact your local distributor. 2. Remove all bolts attaching machine to shipping base. 3. Leave packing mater...

Page 8 - Electrical connections; Controls; Prior to Operation

8 11. Tension the v-belt by pushing down on the motor and tightening the lock handle on the motor tilt plate. Correct tension is achieved when finger pressure between the two pulleys causes approximately a 1/2” deflection. See Figure 4. Figure 4 12. Close pulley cover door and fasten with lock kno...

Page 9 - Adjustments; Adjusting vise square to blade; Adjusting feed rate

9 8. Check to see that coolant level is adequate and turn on coolant pump if material to be cut requires it. Machine should be filled with four gallons of the proper coolant mixture. Follow the directions on the product maker’s label and fill the coolant tank through the chip tray area. 9. Do not ...

Page 10 - Blade tracking adjustment; Automatic shut-off adjustment

10 5. Loosen lock knob and slide left blade guide arm (B) to the right as far as possible. 6. Remove old blade from both wheels and out of each blade guide. Even dull blades are sharp to the skin. Use extra caution handling band saw blades. 7. Install new blade making sure teeth are pointed downwa...

Page 11 - Guide roller adjustment; Maintenance

11 Figure 9 12.8 Guide roller adjustment 1. Disconnect machine from power source. 2. Loosen blade guides (A, Figure 10) by loosening screws (B). Slide blade guides away from blade. Figure 10 3. Loosen locking screws (C) by using a hex wrench. 4. Adjust the eccentric bushings with a combination wre...

Page 12 - Lubrication; Replacement Parts

12 If the power cord is worn, cut, or damaged in any way, have it replaced immediately. 13.1 Lubrication All ball bearings are permanently lubricated and sealed. They require no further attention. The gear box lubricant should be changed after the first 50 hours of operation. Change lubricant from...

Page 13 - HBS-916W & HBS-1018W – Base and Bed Assembly – Exploded View

13 14.1.1 HBS-916W & HBS-1018W – Base and Bed Assembly – Exploded View

Page 14 - HBS-916W only – Saw Arm Assembly – Exploded View

14 14.1.2 HBS-916W only – Saw Arm Assembly – Exploded View

Page 15 - HBS-1018W only – Saw Arm Assembly – Exploded View

15 14.1.3 HBS-1018W only – Saw Arm Assembly – Exploded View

Page 23 - HBS-916W & 1018W – Gear Speed Reducing Box – Exploded View

23 14.2.1 HBS-916W & 1018W – Gear Speed Reducing Box – Exploded View

Page 24 - HBS-916W & 1018W – Gear Speed Reducing Box – Parts List

24 14.2.2 HBS-916W & 1018W – Gear Speed Reducing Box – Parts List Index No. Part No. Description Size Qty 1 ................ HBS916W-94-01 ....... Oil Seal .................................................................... 35x55x8 mm ................. 1 2 ................ HBS916W-94-02 ........

Page 25 - Electrical Connections; Electrical Connections – HBS-916W only

25 15.0 Electrical Connections 15.1 Electrical Connections – HBS-916W only

Page 26 - Electrical Connections – HBS-1018W only