Jet 413451 - User Manual

5 26. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 27. Use recommended accessories; improper accessories may be hazardous. 28. Maintain tools with care. Keep ...

6 5.0 Features Figure 1 1. Blade tension handle 2. Cast iron bow 3. Coolant taps 4. Centralized control switch 5. 4-step pulley system with v-belt 6. 3/4 HP motor 7. Ball bearing blade guides 8. Chip brush 9. Hydraulic cylinder with valve regulator 10. Adjustable work stop 11. Steel stand with coola...

8 7.0 Set-Up and Assembly 7.1 Unpacking and cleanup Inspect contents of shipping container for shipping damage. Report any damage to your distributor. Remove all contents from carton, and compare to the contents list in this manual. Report any part shortages to your distributor. Do not discard carto...

9 Figure 4 7.3 Assembly Refer to Figure 4. Band Saw should be disconnected from electrical power during assembly and setup. 1. Assemble base parts (J,K) according to Figure 4. 2. Install axle and wheels (H, I ). Install cotter pin (HP-9) through hole in axle, and bend back legs of cotter pin to secu...

10 7.4 Vertical cutting plate These steps are only necessary when using band saw in vertical position. 1. Disconnect machine from power source. 2. Open valve on hydraulic cylinder (lever parallel to cylinder) and raise bow to vertical position. 3. Remove two screws and remove seat plate, as shown in...

11 7.6 Coolant system Make sure there is coolant in the tank before operating, to prevent damage to pump. Use of a water-soluble coolant will increase cutting efficiency and prolong blade life. Do not use black cutting oil as a substitute. 1. Remove coolant return hose (A, Figure 10) from filter cup...

13 9.0 Adjustments The settings on your band saw, such as blade squareness and tracking, were carefully performed by the manufacturer. You should, however, verify these before operating, in case misalignment has occurred during shipping. 9.1 Squaring blade to table 1. Disconnect machine from power s...

14 9.4 Miter cuts 1. Loosen handle (G, Figure 17). 2. Rotate bow to desired angle up to 45-degrees, using scale indicator on front of base. 3. Tighten handle. Figure 17 The angle scale is sufficient for most mitering operations. If greater precision is needed, verify setting with a protractor. If ha...

15 2. Raise bow to vertical position, and secure in place by turning off hydraulic cylinder. 3. Remove red blade guard (A, Figure 19) by removing two screws. Red blade guard must be reinstalled after new blade is fitted. Figure 19 4. Remove brush assembly (B, Figure 19) by removing two screws. 5. Lo...

16 Blade tracking has been tested at the factory. Adjustment is rarely required when the blade is used properly and if the blade is correctly welded. If a tracking problem occurs, first inspect blade condition, then adjust tracking as follows: 1. Raise bow to vertical position and secure by turning ...

18 Figure 27 9.13 Chip brush The chip brush (B, Figure 19) must be properly adjusted and maintained in working condition; otherwise damage to blade can occur. Adjust the brush so that its bristles overlap the blade. Replace brush if it becomes worn or damaged. 9.14 Limit switch The stop screw (F, Fi...

19 3. When the saw has completed 1/3 of the cut, increase the feed rate slightly and allow the saw to complete the cut. 4. Keep the same hydraulic cylinder setting and begin a second cut on the same or similar workpiece. 5. When the blade has completed about 1/3 of the cut, increase feed rate. W atc...

20 Place a thin coat of oil on the table surface on which the vise jaw slides. Figure 31 12.1 Coolant level Maintain coolant level. Low coolant level can cause foaming and high blade temperatures. Replace dirty coolant; dirty or weak coolant can clog the pump, cause crooked cuts, a low cutting rate ...

22 14.0 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com). Having the Model Number and Serial Number of your machine available when y...

23 14.1.1 HVBS-710S Table and Stand Assembly – Exploded View

25 14.1.3 HVBS-710S Assembly – Parts List Index No. Part No. Description Size Qty 1 ................ HVBS710S-1G ............... Bottom Pan ......................................................... ...................................... 1 1-1 ............. TS-0060071 ................... Hex Cap Scre...