HP ZR30W - Manuals

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source andconnection appropriate for this monitor. For information on the correct power cord set to use with themonitor, refer to the Power Cord Set R...

Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only thosecontrols that are covered in the operating instructions. If the monitor is not operating properly orhas been dropped o...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master powe...

Routing and Connecting the Cables 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Remove the cable routing cover by pulling it straight off the front of the column. Figure 3-3 Removing the Cable Routing Cover 3. Before connecting the cables, route them through th...

Connecting USB Devices The monitor provides USB connectors on the side panel and on the rear panel that can be used toconnect devices such as a digital camera, USB keyboard, or USB mouse. NOTE: You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0 ports on the mon...

Turning on the Monitor 1. Ensure that the master power switch on the rear of the monitor is in the On position. 2. Press the power button on the computer to turn it on. 3. Press the power button on the front of the monitor to turn it on. CAUTION: Burn-in image damage may occur on monitors that displ...

Removing the Monitor Pedestal Base You can remove the monitor panel from the pedestal base to mount the panel on a wall, a swing arm,or other mounting fixture (purchased separately). This monitor has a Quick Release mechanism that allows you to easily remove and replace the monitorpanel to the pedes...

Mounting the Monitor NOTE: This apparatus is intended to be supported by UL or CSA Listed wall mount bracket. The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. Itallows you to quickly and securely attach the monitor panel to the mounting fixture. 1. Remo...

Locating the Rating Labels The rating labels on the monitor provide the spare part number, product number, and serial number.You may need these numbers when contacting HP about the monitor model. The rating labels arelocated on the rear panel of the monitor display head. Figure 3-14 Locating the Rat...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on the computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● additional software for the monitor model NOTE: If the monitor does not include a CD, the .INF and .I...

Installing the .INF and .ICM Files After you determine that you need to update, you can install the .INF and .ICM files from the CD ordownload them. Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu is di...

Front Panel Controls Table 4-1 Monitor Front Panel Controls Control Function 1 Source Selects the video input (DisplayPort or DVI-D) 2 – (Minus) Reduces the brightness setting. 3 + (Plus) Increases the brightness setting. NOTE: Pressing the + (Plus) and – (Minus) buttons at the same time enables or ...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommendedsolutions. Problem Possible Cause Solution Screen is blank and no LED. Power cord is disconnected. Connect the power cord. Master power switch is turnedoff. S...

B Technical Specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical levelspecifications for performance and actual performance may vary either higher o...

Power Source 100 – 240 VAC, 50/60 Hz Altitude: Operating Storage 0 to 5000 m 0 to 12192 m 0 to 16,400 feet 0 to 40,000 feet Measured Power Consumption: Full Power Typical Settings Sleep Bezel Switch Off <185 watts <130 watts <2 watts <1 watt Input Terminal One DVI connector with cable in...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a resid...

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany The official EU CE declaration of conformity for this device may be found at http://www.hp.com/go/ certificates . German Ergonomics Notice HP products which bear the “GS” approval mark, when forming part of a system co...

Japanese Power Cord Requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Product Environmental Notices Materials Disposal This HP product contains mercury in the fluorescent lamp in the...

11363-2006 11363-2006 Turkey EEE Regulation In Conformity with the EEE Regulation EEE Yönetmeli ğ ine Uygundur ENWW Product Environmental Notices 27

D LCD Monitor Quality and Pixel Policy The TFT monitor uses high-precision technology, manufactured according to HP standards, toguarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections thatappear as small bright or dark spots. This is common to all LCD displays ...