HP ZR22W - Manuals

2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source andconnection appropriate for this monitor. For information on the correct power cord set to use with themonitor, refer to the Power Cord Set R...

Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only thosecontrols that are covered in the operating instructions. If the monitor is not operating properly orhas been dropped o...

3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master powe...

Routing and Connecting the Cables 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Remove the cable routing cover by pulling it straight off the front of the column. Figure 3-3 Removing the Cable Routing Cover 3. Before connecting the cables, route them through th...

Connecting USB Devices The monitor provides USB connectors on the side panel and on the rear panel that can be used toconnect devices such as a digital camera, USB keyboard, or USB mouse. NOTE: You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0 ports on the mon...

4. Raise the monitor panel to its highest position and pivot the monitor clockwise from landscape toportrait orientation viewing to adapt to your application. NOTE: It may be necessary to tilt the monitor panel back to prevent the corner of the panel from coming in contact with the base when pivotin...

The monitor automatically scans the signal inputs for an active input and uses that input for the display.If two or more inputs are active, the monitor will display the default input source. If the default source isnot one of the active inputs, then the monitor will display the highest ranking prior...

Mounting the Monitor NOTE: This apparatus is intended to be supported by UL or CSA Listed wall mount bracket. The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. Itallows you to quickly and securely attach the monitor panel to the mounting fixture. 1. Remo...

Locating the Rating Labels The rating labels on the monitor provide the spare part number, product number, and serial number.You may need these numbers when contacting HP about the monitor model. The rating labels arelocated on the rear panel of the monitor display head. Figure 3-15 Locating the Rat...

4 Operating the Monitor Software and Utilities The CD that comes with the monitor contains files you can install on the computer: ● an .INF (Information) file ● an .ICM (Image Color Matching) file ● auto-adjustment pattern utility ● additional software for the monitor model NOTE: If the monitor does...

Installing the .INF and .ICM Files After you determine that you need to update, you can install the .INF and .ICM files from the CD ordownload them. Installing from the CD To install the .INF and .ICM files on the computer from the CD: 1. Insert the CD in the computer CD-ROM drive. The CD menu is di...

Using the Auto-Adjustment Function You can optimize the screen performance for the VGA (analog) input by using the OK/auto button on the monitor and the auto-adjustment pattern software utility on the CD provided. Do not use this procedure if the monitor is using a DVI or DisplayPort input. If the m...

Front Panel Controls Table 4-1 Monitor Front Panel Controls Control Function 1 Menu Opens, selects or exits the OSD menu. 2 Minus If the OSD menu is on, press to navigate backward throughthe OSD menu and decrease adjustment levels. 3 Plus/source If the OSD menu is on, press to navigate forward throu...

Adjusting the Monitor Settings The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP DisplayAssistant utility. NOTE: If there is a problem with the display settings, try resetting the settings to the factory defaults by opening the OSD and selecting Factory Reset ...

OSD Menu Selections The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions.After changing an OSD menu item, and if the menu screen has these options, you may choose to: ● Cancel —to return to the previous menu level. ● Save and Return —to save all cha...

Optimizing Digital Conversion Two controls in the on-screen display can be adjusted to improve image performance: Clock and ClockPhase. NOTE: The Clock and Clock Phase controls are adjustable only when using an analog input. These controls are not adjustable for digital inputs. The Clock must first ...

Identifying Monitor Conditions Special messages will appear on the monitor screen when identifying the following monitor conditions: ● Monitor Status —When the monitor is powered on or when the input source signal is changed, a Monitor Status message is displayed for five seconds. The message shows ...

Sleep Timer Mode The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor topower on and off at the same time every day. This also extends the life of the backlight bulbs in themonitor. The Sleep Timer has five settings: ● Set Current Time ● Set Sleep Time ● Se...

HP Display LiteSaver HP Display LiteSaver is a software application, available on the CD, that increases monitor life andsaves energy. It allows you to place the monitor into its low power sleep mode at predefined times byshutting down or reducing power to most internal circuits. This helps protect ...

sRGB Support The monitor is designed to support sRGB for color management, which adapts to the color standardsused in the image technology industry. To take advantage of the sRGB support, you will need to change the monitor’s color temperature to sRGB and install the sRGB color profile (ICM) file. N...

8. Select the RGB Color Space Profile.icm file, then click the OK button. 9. To activate a color profile for the monitor, you must set it as the Default Monitor Profile. Select sRGB Color Space Profile , then click the Set as Default button. Installing the sRGB ICM File for Microsoft Windows 7 1. Cl...

A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommendedsolutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord. Master power switch on themonitor's rear panel...

Problem Possible Cause Solution Input Signal Out of Range. ChangeSettings to 1920 × 1080 @ 60Hz (ZR22w model) OR Input Signal Out of Range. Change settings to 1920 x1200 @ 60 Hz (ZR24w model) is displayed on screen. Video resolution and/or refreshrate are set higher than whatthe monitor supports. Re...

B Technical Specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical levelspecifications for performance and actual performance may vary either higher o...

Vertical Refresh Rate 59 to 61 Hz Environmental Requirements Temperature Operating Temperature Storage Temperature 5 to 35° C -20 to 60° C 41 to 95° F -4 to 140° F Relative Humidity 20 to 80% Power Source 100 – 240 VAC, 50/60 Hz Altitude: Operating Storage 0 to 5000 m 0 to 12192 m 0 to 16,400 feet 0...

14 1440 × 900 55.94 59.89 15 1440 × 900 55.469 59.901 16 1600 × 900 60.0 60.0 17 1600 × 1000 61.648 60.00 18 1600 × 1200 75.00 60.00 19 1680 × 1050 65.29 60.00 20 1920 × 1080 67.5 60.00 ZR24w Model Table B-4 Factory Preset Modes Preset Pixel Format Horz Freq (kHz) Vert Freq (Hz) 1 640 × 480 31.469 5...

Energy Saver Feature When the monitor is in its normal operating mode, the monitor uses less than 28.5 watts (ZR22w model)or 95 watts (ZR24w model) and the Power light is blue. The monitor also supports a reduced power state. The reduced power state will be entered into if themonitor detects the abs...

C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a resid...

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany The official EU CE declaration of conformity for this device may be found at http://www.hp.com/go/ certificates . German Ergonomics Notice HP products which bear the “GS” approval mark, when forming part of a system co...

Japanese Power Cord Requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Product Environmental Notices ENERGY STAR® Qualification (Select Models) HP Displays marked with the ENERGY STAR...

11363-2006 11363-2006 Turkey EEE Regulation In Conformity with the EEE Regulation EEE Yönetmeli ğ ine Uygundur 44 Appendix C Agency Regulatory Notices ENWW

D LCD Monitor Quality and Pixel Policy The TFT monitor uses high-precision technology, manufactured according to HP standards, toguarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections thatappear as small bright or dark spots. This is common to all LCD displays ...