HP R5000 - Manuals

Component identification 8 UPS front panel controls Item Component Description 1 ESC button Cancel/return to the previous menu 2 Up arrow Scroll through the menu structure 3 Down arrow Scroll through the menu structure 4 Enter/select button Select an option 5 Power on/off button • Green—operating • ...

Component identification 9 Item Description 1 ERM connector for the small plug on the split ERM cable 2 Load segment 1 circuit breaker (controls the C19 and C13 receptacles, but does not control the large output receptacle) 3 Load segment 1 (two IEC-320-C19 receptacles and two IEC-320-C13 receptacle...

Component identification 10 ERM rear panel Item Description 1 ERM input connector for the small plug on the split ERM cable of another ERM output 2 ERM input connector for the large plug on the split ERM cable of another ERM output 3 Split ERM cable with two output connectors that attach to the UPS ...

Installation and configuration 11 Installation and configuration Precautions Save these instructions. This document contains important safety instructions that should be followed during installation, operation, and maintenance of the UPS and batteries. WARNING: A risk of personal injury from electri...

Installation and configuration 12 • Hex nuts • Cage nuts • Cage nut-fitting tool Selecting a site WARNING: To prevent fire or electric shock, install the unit in a temperature- and humidity-controlled indoor environment, free of conductive contaminants. When selecting a site, consider the following ...

Installation and configuration 16 7. Install the rear mounting brackets using hex nuts. Wait until the unit is installed and the brackets are adjusted before tightening the nuts. Preparing the rails for integrated shipping If the unit is to be shipped in an HP 9000 or 10000 series rack: 1. Remove th...

Installation and configuration 17 Installing the UPS Before installing the UPS, review and observe all warnings in "Precautions (on page 11 )." WARNING: A risk of personal injury or damage to the equipment exists. Uneven loading of equipment in the rack might cause the rack to become unstabl...

Installation and configuration 18 Attaching the UPS front bezel Connecting the serial communications port CAUTION: Use only the computer interface cable supplied with the UPS to connect the communications port to the host computer. IMPORTANT: Power protector software requires the communications port...

Installation and configuration 19 Configuring a USB to serial converter NOTE: This procedure was tested on the Windows ® XP Professional, Windows Server ® 2003, and Windows ® Vista Enterprise operating systems using the HP USB to serial converter (part number 304098-001). Depending on your system co...

Installation and configuration 20 o Bits per second: 9600 o Data Bits: 8 o Parity: None o Stop bits: 1 o Flow control: None 9. Click Advanced . The Advanced Settings screen appears. 10. From the COM Port Number drop down menu, select Com 1 for the USB port number, and then click OK . If COM 1 is bei...

Installation and configuration 21 b. Click Scan for hardware changes to refresh the screen and display the changes. Connecting the USB communications port NOTE: This port is only used for firmware upgrades. For additional information, see "Updating the UPS firmware (on page 43 )." Connecting...

Installation and configuration 23 Connecting the ground bonding cable The ground bonding screw is provided as an attachment point for conductors. Use a ground bonding cable if the rack contains any conductors for the purpose of functional grounding or bonding of ungrounded metal parts. The ground bo...

Installation and configuration 24 To configure the UPS Network Module, see "Configuring the UPS Network Module (on page 25 )." Connecting the UPS to utility power WARNING: To prevent injury from electric shock or damage to the equipment: • Plug the input line cord into a grounded (earthed) e...

Installation and configuration 25 Connecting the UPS cord retention clips Charging the UPS batteries With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to devices. The ba...

Installation and configuration 26 2. Connect the RJ-45 connector on the DB-9 to RJ-45 cable to the Settings/AUX connector on the UPS Network Module. This connection is used to access and configure the UPS Network Module network settings locally through a terminal emulation program. Launching a termi...

Installation and configuration 27 2. At the prompt, enter admin . The HP UPS Network Module Configuration Menu appears. Use the HP UPS Network Module Configuration Menu to configure the minimum settings required to access the UPS Network Module remotely. IMPORTANT: The IP address assigned to the UPS...

Installation and configuration 28 5. Click Sign In. The HP UPS Network Module web interface appears. Configuring the UPS Network Module settings Use the Settings screens of the HP UPS Network Module web interface to configure the UPS Network Module. For more information, see the HP UPS Network Modul...

Installation and configuration 29 3. Install the mounting ears on the chassis using the screws provided. 4. With one person on each side, lift the chassis to rail level and slide the chassis on the mounting rails. Be sure that the cleat brackets slide into the channels on the rear stabilization brac...

Installation and configuration 30 Connecting the ERM to the UPS Connect both ends of the split ERM cable to the ERM connectors on the UPS rear panel. To install additional ERMs, connect both ends of the split ERM cable from the next ERM into the connectors on the rear panel of the previous ERM. Up t...

UPS operations 31 UPS operations Modes of operation The UPS has three modes of operation: • Standby mode (on page 31 ) • Operate mode (on page 31 ) • Auto-Bypass mode (on page 31 ) Standby mode In Standby mode: • No power is available at the UPS output receptacles. • The UPS charges the batteries as...

UPS operations 32 • Over temperature • Output short • Hardware failure Transferring the UPS between modes To transfer between Operate mode and Bypass mode: 1. Press the ESC button to activate the menu options. 2. Press the down arrow to scroll to the Control menu, and then press the Enter button. 3....

UPS operations 33 Main menu Submenu Display information or menu function — Battery status Battery Charging/Floating/Resting, Charge Level, ERM Number, and Runtime Event Log — Displays events and alarms Measurements Output Output watts and VA — Output Output amps and power factor — Output Output volt...

UPS operations 34 1. Initiate a REPO by closing the REPO contact. CAUTION: If the polarity is reversed while connecting the REPO port, the UPS powers up normally. 2. Verify proper connection of the REPO port: a. Power up the UPS by pressing the Power button. b. Disconnect the REPO port. c. Reconnect...

Power management 35 Power management Power Protector software HP Power Protector software ensures maximum power reliability of computer systems through comprehensive control of UPSs. The easy-to-use browser interface enables novice users to configure and manage power protection settings. To download...

Maintenance 37 Maintenance Removing the UPS front bezel Removing the ERM front bezel Replacing the UPS Network Module This component is hot-swappable and can be replaced without powering down the UPS.

Maintenance 38 1. (optional) To replace the component with the UPS powered down, refer to "Powering down the UPS (on page 34 )." 2. Disconnect all cables attached to the UPS Network Module connectors. 3. Remove the two screws securing the UPS Network Module and slide the module out. To repla...

Maintenance 39 WARNING: To prevent personal injury, prepare the area and observe all materials-handling procedures when transporting a battery module. Battery modules weigh 11.1 kg (24.47 lb). NOTE: Replace all battery modules at the same time with the same type of batteries originally installed in ...

Maintenance 41 To replace the component, reverse the removal procedure. IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to devices. The batteries charge to: • 80 percent of their capacity within 3 hours • 100 percent of their capacity within 48 hours Replacing the...

Maintenance 43 8. Remove the UPS battery modules. 9. Remove the screws securing the UPS to the rack. 10. Remove the UPS from the rack. To replace the component, reverse the removal procedure. Replacing the ERM To remove the ERM: 1. Disconnect all cabling. 2. Remove the front bezel (" Removing th...

Troubleshooting 44 Troubleshooting Alarm troubleshooting This UPS is designed for durable, automatic operation and also to alert you whenever potential operating problems might occur. Usually the alarms shown on the control panel do not mean that the output power is affected. Instead, they are preve...

Troubleshooting 46 Silencing an audible alarm To silence an alarm, press any button on the front panel display to silence the alarm. If the alarm status changes, the alarm beeps again, overriding the previous alarm silencing. IMPORTANT: • Although the audible alarm silences, the condition that cause...

Troubleshooting 47 a. Power down the UPS (" Powering down the UPS " on page 34 ). b. Remove one or more load devices to reduce the power requirements. c. Wait at least 5 seconds and restart the UPS. d. If the condition persists, verify that the load devices are not defective. 4. Allow the UP...

Troubleshooting 49 1. Check the input voltage and reconfigure the UPS (" Configuring the UPS " on page 32 ). 2. Contact a qualified electrician to verify that the utility power is suitable for the UPS. UPS is in Auto-Bypass mode Action : 1. If power management software is being used, check t...

Specifications 50 Specifications UPS physical specifications Parameter Value Height 12.7 cm (5 in) Depth 74.4 cm (29.3 in) Width 43.7 cm (17.2 in) Weight 57 kg (126 lb) ERM physical specifications Parameter Value Height 12.7 cm (5 in) Depth 71.9 cm (28.3 in) Width 43.8 cm (17.24 in) Weight 63 kg (13...

Specifications 52 Feature Specification Surge suppression High-energy 6500 A peak Noise filtering MOVs and line filter for normal and common mode use Battery specifications Feature Specification Type Each model contains maintenance-free, sealed, valve regulated lead-acid batteries with an 8-year min...

Specifications 53 Environmental specifications Feature Specification Operating temperature 10°C to 40°C (50°F to 104°F); UL-tested at 25°C (77°F) Nonoperating temperature -25°C to 55°C (-13°F to 131°F) Relative humidity 20% to 80%; noncondensing Operating altitude Up to 2,000 m (6,600 ft) above sea ...

Spares 54 Spares Ordering spares To order a spare, visit the HP website

Regulatory information 55 Regulatory information Safety and regulatory compliance For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products , available at the HP website ( http://www.hp.com/support/Safety-Co...

Regulatory information 56 Limited warranty To back up the wide range of features offered with the UPS, a 3-year limited warranty is provided. $250,000 Computer Load Protection Guarantee In addition to the limited warranty, a $250,000 Computer Load Protection Guarantee (provided by the original equip...

Electrostatic discharge 57 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boar...

Support and other resources 58 Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log (HP ProLiant Gen8 or later products) Download and have available an Active Health System log for 3 days before the failu...

Acronyms and abbreviations 59 Acronyms and abbreviations ERM extended runtime module IEC International Electrotechnical Commission PDU power distribution unit PFC power factor corrected REPO remote emergency power off RMS root-mean-square UPS uninterruptible power system

Documentation feedback 60 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback

Index 61 A authorized reseller 58 B backup time, insufficient 48 batteries, care and storage 39 batteries, charging 25 batteries, replacing 38, 39 battery replacement notice 55 battery warranty 55 bezel, removing 37 BSMI notice 55 buttons 7, 8 C Canadian notice 55 charging batteries 25 circuit break...