Page 2 - HP Kayak XM600 PC Workstation System Board
Installing and Replacing Hardware Parts in Your PC Workstation 2 HP Kayak XM600 PC Workstation System Board HP Kayak XU800 PC Workstation System Board Up to six accessory cards can be installed:- One Universal AGP PRO (graphics)- Five 32-bit PCI slots Support for one or two processors Floppy Disk Dr...
Page 3 - Removing and Replacing the Cover and Front Bezel; Tilt the cover sidewards, then lift off the PC Workstation chassis.
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Cover and Front Bezel 3 Removing and Replacing the Cover and Front Bezel Removing the Cover For your own safety, it is recommended that you first read the warning notices on in the Introductory Section. 1 Switc...
Page 4 - NOTE
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Cover and Front Bezel 4 NOTE Take care when removing the upper and lower bezels. They are not on a hinge, so do not force them open. To remove the upper and lower bezels: a Unclip the two clips located on the l...
Page 5 - Removing and Replacing the Airflow Guide
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Airflow Guide 5 Removing and Replacing the Airflow Guide Removing the HP UltraFlow Airflow Guide 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables...
Page 6 - Removing and Replacing a Processor; Remove the PC Workstation’s cover (refer to page 3 for instructions).
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing a Processor 6 Removing and Replacing a Processor Single-processor systems can be upgraded to dual-processor systems by installing a second processor in the vacant processor slot. The second processor must be of the...
Page 8 - Upgrading SDRAM Memory; Removing and Replacing an SDRAM Module
Installing and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on HP Kayak XM600 Models Shipped with SDRAM 8 Removing, Replacing and Upgrading Memoryon HP Kayak XM600 Models Shipped with SDRAM Upgrading SDRAM Memory SDRAM models of the HP Kayak XM600 are supp...
Page 9 - completely; Removing and Replacing the Memory Expansion Card
Installing and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on HP Kayak XM600 Models Shipped with SDRAM 9 5 To install a module, ensure that the two notches of the memory module are aligned with those of the socket. With the two retaining clips open, press...
Page 11 - Upgrading RDRAM Memory; Removing and Replacing an RDRAM Module
Installing and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on HP Kayak XM600 Models Shipped with RDRAM 11 Removing, Replacing and Upgrading Memoryon HP Kayak XM600 Models Shipped with RDRAM Upgrading RDRAM Memory RDRAM models of the HP Kayak XM600 PC Work...
Page 13 - Memory Upgrades on the HP Kayak XU800; ECC Type; . Speed ratings for RIMM modules exist between: PC600
Installing and Replacing Hardware Parts in Your PC Workstation Memory Upgrades on the HP Kayak XU800 13 Memory Upgrades on the HP Kayak XU800 There is a single Memory Expansion Card connector on the system board that supports a Memory Expansion Card installed with either RIMM or DIMM sockets. NOTE D...
Page 15 - Removing and Replacing a Memory Module
Installing and Replacing Hardware Parts in Your PC Workstation Memory Upgrades on the HP Kayak XU800 15 8 Remove memory modules and any continuity modules from the old Memory Expansion Card, then install them in the same positions on the new Memory Expansion Card. Replacing the Memory Expansion Card...
Page 17 - Removing and Replacing a PCI Accessory Card; HP Kayak XM600 Upgrades; There are five PCI accessory card slots:
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing a PCI Accessory Card 17 Removing and Replacing a PCI Accessory Card To remove or install an accessory card, complete the following steps: 1 Switch off the display and PC Workstation. Disconnect all power cables and...
Page 18 - Universal AGP PRO slot (Kayak XM600 and Kayak XU800)
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing a PCI Accessory Card 18 The following table shows the various PCI card installations for the different PCI slots on the HP Kayak XU800: Universal AGP PRO slot (Kayak XM600 and Kayak XU800) PCI Card 5 V 3.3 V Univer...
Page 19 - Installing Mass Storage Devices
Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices 19 Installing Mass Storage Devices The PC has an integrated Ultra ATA-66 controller that supports up to four IDE devices. Removable media IDE devices, such as CD-ROM drives, DVD drives, tape drives and Zip...
Page 20 - The third cable has one connector for a floppy drive.; HP Kayak XM600 Cables and Connectors
Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices 20 • The ATA IDE cable supports two IDE devices. This cable is connected to the Primary IDE connector on the system board. The bootable hard disk drive is connected to this cable via the MASTER connector. ...
Page 21 - HP Kayak XU800 Cables and Connectors; If you are installing an additional SCSI drive,; you should assign an; SCSI IDs range from 0 to 15 for
Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices 21 HP Kayak XU800 Cables and Connectors Which SCSI Connectors to Use There is an internal SCSI connector on the system board that enables you to connect up to five internal SCSI devices. The last connector...
Page 22 - Power Connectors for HP Kayak XM600 and XU800 PCs
Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices 22 You should assign an unused SCSI ID to the second SCSI hard disk drive (for example, SCSI ID 1). The SCSI ID is usually configured with jumpers on the SCSI hard disk drive. Refer to the installation gui...
Page 23 - Removing and Replacing the Primary Hard Disk Drive; CAUTION
Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Primary Hard Disk Drive 23 Removing and Replacing the Primary Hard Disk Drive CAUTION Handle the hard disk drive with care. Avoid shocks and violent movement as this can cause damage to the hard disk drive’s in...
Page 25 - Installing a Second Hard Disk Drive in an Internal Shelf; To install a second hard disk drive:; Installing a Third Hard Disk Drive
Installing and Replacing Hardware Parts in Your PC Workstation Installing a Second Hard Disk Drive in an Internal Shelf 25 Installing a Second Hard Disk Drive in an Internal Shelf The internal shelves can support two 3.5-inch devices. The master hard disk drive must be installed in the top shelf whe...
Page 26 - Installing an Accessory in the Front Access Cage; Depending on the accessory to be installed, either:
Installing and Replacing Hardware Parts in Your PC Workstation Installing an Accessory in the Front Access Cage 26 Installing an Accessory in the Front Access Cage 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Works...
Page 27 - Connect the power and data cables to the installed device.
Installing and Replacing Hardware Parts in Your PC Workstation Installing an Accessory in the Front Access Cage 27 5 Align the guide rails on both sides of the drive with the internal shelf guides and then slide the drive until it clicks into position. 6 Connect the power and data cables to the inst...
Page 28 - Disconnect the power and data cables from the old drive.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the CD-ROM Drive (or DVD-Drive) 28 Replacing the CD-ROM Drive (or DVD-Drive) Removing theOld Drive 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the ...
Page 29 - Replacing the Floppy Disk Drive
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Floppy Disk Drive 29 Replacing the Floppy Disk Drive Removing the Floppy Disk Drive 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstat...
Page 30 - Completing the Installation of a Mass Storage Device; Advanced
Installing and Replacing Hardware Parts in Your PC Workstation Completing the Installation of a Mass Storage Device 30 Completing the Installation of a Mass Storage Device When an IDE Drive Is Installed 1 Switch on the computer. 2 If an error message appears, follow the instructions provided by the ...
Page 31 - Replacing the Power Supply Unit; WARNING
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Power Supply Unit 31 Replacing the Power Supply Unit WARNING Hewlett-Packard does not support power supply upgrades. This information is provided to help you replace a defective power supply unit. For your safety, only repl...
Page 32 - Insert the new power supply unit.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Power Supply Unit 32 Installing the Power Supply Unit 1 Insert the new power supply unit. 2 Secure it in position using the three screws that you removed in steps 6 and 7. 3 Reconnect all internal power supply connectors. 4...
Page 33 - Replacing the System Board
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the System Board 33 Replacing the System Board Removing the System Board 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation’s cover (re...
Page 34 - Clip the retaining bracket onto the new system board.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the System Board 34 Installing the New System Board 1 Clip the retaining bracket onto the new system board. 2 Lower the system board onto the guide pins ensuring that all hooks are correctly positioned. Check that the rear conn...
Page 35 - Replacing the Rear Fan
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Rear Fan 35 Replacing the Rear Fan Removing theRear Fan 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation’s cover (refer to page 3...
Page 36 - Align the processor fan clips with their corresponding sockets.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Rear Fan 36 Replacing theRear Fan 1 The rear fan can only be installed in one way. From the rear of the PC Workstation, the two retaining clips should be positioned on the same side as the chassis edge. 2 Connect the rear f...
Page 37 - Replacing the Fan and Speaker Assembly; Remove the PC chassis retaining bar.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Fan and Speaker Assembly 37 Replacing the Fan and Speaker Assembly Removing the Fan and Speaker Assembly 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 R...
Page 38 - Replace the screw on the front of the chassis.
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Fan and Speaker Assembly 38 Replacing the Fan and Speaker Assembly 1 Place the fan and speaker assembly behind the internal shelves (the speaker should be near the bottom edge of the chassis and facing towards the front of ...
Page 39 - System Board Switches; HP Kayak XM600 PC Workstation
Installing and Replacing Hardware Parts in Your PC Workstation System Board Switches 39 System Board Switches HP Kayak XM600 PC Workstation There are ten system board switches used for configuration, numbered from 1 to 10. Of these a certain number are reserved and should not be modified, otherwise ...
Page 40 - HP Kayak XU800 PC Workstation
Installing and Replacing Hardware Parts in Your PC Workstation System Board Switches 40 HP Kayak XU800 PC Workstation There are ten system board switches used for configuration, numbered from 1 to 10. Of these a certain number are reserved and should not be modified, otherwise it could lead to a sys...
Page 41 - Replacing the Battery
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Battery 41 Replacing the Battery WARNING There is a danger of explosion if the battery is incorrectly installed. For your safety, never attempt to recharge, disassemble, or burn the old battery. Replace the battery only wit...
