Page 2 - Printed in Australia; Copyright; Setting Up the STM-1 Electrical Interface Pod
The information contained in this document is subject to change without notice. HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL,INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable...
Page 3 - iii; Contents
iii Contents Guide to the HP E5200A Broadband Service Analyzer Documentation ........ ivAbout the STM-1 Electrical Interface Pod....................................................... 1Online Help ..........................................................................................................
Page 4 - Guide to the HP E5200A Broadband Service Analyzer Documentation
Guide to the HP E5200A Broadband Service Analyzer Documentation iv Guide to the HP E5200A Broadband ServiceAnalyzer Documentation The HP E5200A Broadband Service Analyzer comes with a comprehensive setof paper and online documentation. Use the following table to determinewhich documents you should u...
Page 5 - About the STM-1 Electrical Interface Pod; Overview
1 About the STM-1 Electrical Interface Pod About the STM-1 Electrical Interface Pod Overview The HP E5123A STM-1 Electrical Interface Pod is a self-contained, plug-inmodule. You use it in conjunction with the HP E5200A Broadband ServiceAnalyzer to test and analyze a system under test (SUT). In the t...
Page 6 - Online Help; User Online Help; User Online Help
Online Help 2 Online Help The User Online Help provides all the information you need to use the analyzer. Use the following sections to learn how to perform tasks : • Getting started • Monitoring • Capturing • Running tests • Simulating • System administration Use the Reference section to find infor...
Page 7 - Front Panel at a Glance; Access
3 Front Panel at a Glance Front Panel at a Glance Access (green LED) Lights each time the interface pod is accessed by thenetwork. Signal (yellow LED) Lights when a valid signal is present at the input connector. In (BNC) Accepts an electrical signal from the SUT. Out (BNC) Provides a signal to the ...
Page 8 - To Set Up the Interface Pod; Caution; Insert the interface pod into the analyzer.
To Set Up the Interface Pod 4 To Set Up the Interface Pod Caution Handle the interface pod with care to avoid electrostatic discharge (ESD)damage during unpacking, installation, and operation. The connectors onthe front and rear of the interface pod are susceptible to ESD. 1 Insert the interface pod...
Page 9 - To Insert the Interface Pod; Insert the interface pod into Port 1 or Port 2 of the analyzer.
5 To Set Up the Interface Pod To Insert the Interface Pod You can insert and remove interface pods at any time, even when theanalyzer is powered on. Initially, you insert an interface pod when you setup the analyzer. Subsequently, you insert an interface pod when youchange the physical layer interfa...
Page 10 - To Remove the Interface Pod; Obtain a pair of 75
To Set Up the Interface Pod 6 To Remove the Interface Pod When you remove the interface pod, make sure you store it in a dust freelocation that meets the environmental requirements listed in“Environmental Specifications” on page 13. An electrostatic-safe bag hasbeen supplied for the storage of each ...
Page 11 - Common system connections and test connections are
7 To Set Up the Interface Pod Common system connections and test connections are • non-intrusive system connection—T-piece and passive testconnections • intrusive system connection—network element, remote loopback, andin-line test connections • diagnostic system connection—transmit loopback and exte...
Page 12 - Automatic Configuration Parameters; 0 dB input gain off; See also
To Set Up the Interface Pod 8 Automatic Configuration Parameters After you insert the interface pod and connect it to the SUT, the analyzerautomatically configures to the STM-1 electrical signal. The analyzer sets the remaining physical layer receive and transmitparameters to the following defaults:...
Page 13 - To Manually Configure the Interface Pod; Note; windows to reflect the new configuration parameters.
9 To Set Up the Interface Pod To Manually Configure the Interface Pod Note When the configuration is complete, the analyzer updates all relevant screens and windows to reflect the new configuration parameters. 1 From the Configuremenu, select theappropriate port;then select Set Up. Click Auto to set...
Page 14 - What to Do Next; The interface pod is now ready for use.
What to Do Next 10 What to Do Next The interface pod is now ready for use. See the User Online Help to find out the different tasks you can perform using the analyzer and interface pod.
Page 15 - Standards and Specifications; Communications Standards; Network Node Interface for the Synchronous Digital Hierarchy
11 Standards and Specifications Standards and Specifications Communications Standards ITU-T G.703 Physical/Electrical Characteristics of Hierarchical Digital Interfaces ITU-T G.708 Network Node Interface for the Synchronous Digital Hierarchy ITU-T G.709 Synchronous Multiplexing Structure ITU-T I.432...
Page 16 - Input and Output Specifications; Transmit Levels
Standards and Specifications 12 Input and Output Specifications Transmit Levels Receive Levels Parameter Nominal Min. Max. Notes Signal level 1.0 V (pp) 0.9 V (pp) 1.1 V (pp) complies with ITU-T G.703 Line rate 155.52 Mb/s –4.6 ppm +4.6 ppm using internal frequency reference Line jitter complies wit...
Page 21 - Right; DECLARATION OF CONFORMITY; declares that the product:; conforms to the following product specifications:; Graeme Cobb - Quality Manager
page inner margin hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line outer margin for text and artwork Right body text drop top margin for modules DECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and EN 45014 Manufacturer’s Name...
Page 22 - Left
body text drop hanging column right margin body text left margin body text bottom margin footer rulling line footer text base line inner margin for text and artwork page inner margin Left top margin for modules
