Page 2 - Notice
ii Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to thismaterial, including, but not limited to, the implied warranties ofmerchantability and fitness for a particular purpose. Hewlett-Packard shallnot ...
Page 3 - Contents
iii Contents Setting Up the HP NetServer E 800................................................................. 1 Introduction ................................................................................................... 1 Step 1: Attaching all the Cables..........................................
Page 5 - Setting Up the HP NetServer E 800; Introduction
1 Setting Up the HP NetServer E 800 Introduction This installation guide is a quick reference for HP NetServer E 800 installation.Skip any steps that do not apply to your installation. Refer to the figures belowfor connection and operating information. For more information, refer to theHP NetServer ...
Page 6 - Step 1: Attaching all the Cables; NOTE
Setting Up the HP NetServer E 800 2 Step 1: Attaching all the Cables If you are not installing any accessories, attach all available cables to therespective connectors, then go to "Step 7: Configuring the HP NetServer." NOTE The two USB connectors are reserved for printers, scanners,and exte...
Page 7 - Step 2: Opening the HP NetServer; ⁄4 inch flat-blade screwdriver; WARNING
Setting Up the HP NetServer E 800 3 Step 2: Opening the HP NetServer Tools Required: • ¼ inch flat-blade screwdriver • Torx T-15 driver WARNING Before removing the cover, always disconnect the power cordand remove the telephone cable. Disconnect the power cord to avoid exposure to high energylevels ...
Page 8 - Front of Chassis
Setting Up the HP NetServer E 800 4 Front of Chassis Bottom of Chassis Cover Cover Latch Opening Air DuctLatch
Page 9 - Step 3: Installing Memory; Ensure both latches close on the DIMM when completely installed.; System Board
Setting Up the HP NetServer E 800 5 Step 3: Installing Memory • Use only HP DIMMs, which are 3.3V, 168-pin, PC133 (133 MHz),buffered SDRAM DIMMs in 128 MB, 256 MB, or 512 MB. • DIMMs may be installed in any slot, in any combination (sizes mixed), inany order, but HP recommends starting at slot 0 and...
Page 10 - Step 4: Installing Mass Storage Devices; The NetServer is internally limited to 7 mass storage shelves.; CAUTION; Remove the Drive Cage by loosening the three captive screws.
Setting Up the HP NetServer E 800 6 Step 4: Installing Mass Storage Devices • The NetServer is internally limited to 7 mass storage shelves. The flexible disk drive and CD-ROM drive, which are standard on allmodels of the HP NetServer E 800, occupy shelves 1 and 2 respectively. • If a backup tape dr...
Page 11 - Slots for Tabs
Setting Up the HP NetServer E 800 7 3. Connect the cables (data & power). 4. Replace the drive cage. Slots for Tabs Captive Screws (3) First insert screws through round holes in back(one on each side). Tabs(2) CAUTION All mounting screws used to thread into the hard disk drivemust be #6-32 and n...
Page 12 - and connect to the SCSI drives or optional backup tape drive.; Terminator
Setting Up the HP NetServer E 800 8 5. If necessary, install the internal accessory SCSI cable into SCSI channel B and connect to the SCSI drives or optional backup tape drive. Use HP NetServer E 800 External/Internal SCSI Cable Kit, part numberP1773A. SCSI BConnector Terminator SCSIConnectors (2) N...
Page 13 - and connect to the knock-out in the rear of the chassis.
Setting Up the HP NetServer E 800 9 6. If necessary, install the external/internal SCSI cable into SCSI channel B and connect to the knock-out in the rear of the chassis. Use HP NetServer E 800 External/Internal SCSI Cable Kit, part numberP1774A. WARNING Ensure you do not touch the sharp metal edges...
Page 14 - Step 5: Installing Adapter Boards; PCI Slots; Slots 1 through 4; PCI Board’s Plastic Extension
Setting Up the HP NetServer E 800 10 Step 5: Installing Adapter Boards • The NetServer E 800 has two PCI (Primary and Secondary) busses andboth are pear-to-pear, which provides approximately equal performance,except when using the two 64-bit slots versus the 32-bit slots. PCI Slots PCI Bus Slots 1 t...
Page 15 - PCI Slot 5
Setting Up the HP NetServer E 800 11 Full-Length PCI Slot 5 PCI Slot 1 PCI Slot 6 PCI Slot 2 PCI Slot 7 64-bit 32-bit 32-bit 32-bit 64-bit System Board (Top View) Wake-On-LAN
Page 16 - Slot Cover
Setting Up the HP NetServer E 800 12 Slot Cover Chassis Cross-SectionView
Page 18 - Step 6: Installing a Second Processor; Both processors must have the same clock speed and cache size.
Setting Up the HP NetServer E 800 14 Step 6: Installing a Second Processor • Both processors must have the same clock speed and cache size. • Use only processor upgrade kits with the same HP product number. This ensures the product numbers are compatible and the processor type,clock speed, and cache...
Page 19 - The ZIF lever must open completely to a full 90; Processor Socket
Setting Up the HP NetServer E 800 15 1. Open the ZIF (Zero Insertion Force) lever on the processor socket. The ZIF lever must open completely to a full 90 ° before removing the terminator from the socket. 2. Remove the terminator from the processor socket. ZIFLever Processor Socket Terminator NOTE R...
Page 20 - The ZIF lever should click when closed.
Setting Up the HP NetServer E 800 16 3. Insert the processor into socket, matching pin-1 to marker. Pin-1Marker 4. Close the ZIF lever with a click. The ZIF lever should click when closed.
Page 21 - Tab
Setting Up the HP NetServer E 800 17 5. Place the Heatsink-Fan on top of processor and follow the steps A-C in the figure below. Hook Latch(hidden) ProcessorSocketBase Thumb Latch Tab Tab A. Rotate and hook. B. Rotate back and hook the Thumb Latch. C. Ensure this ridge rests between the CPU and the ...
Page 22 - CPU 1 Fan
Setting Up the HP NetServer E 800 18 6. Connect the fan connector to the respective connector on the system board. Processor 1 (CPU 1) Processor 2(CPU 2) CPU 1 Fan CPU 2 Fan SystemFan PowerConnector CAUTION Failure to connect the fan connector will cause the processorto overheat and the NetServer wi...
Page 23 - Step 7: Configuring the HP NetServer; Power on the HP NetServer and the monitor:; Insert the HP NetServer Navigator CD-ROM in the CD-ROM drive.; Press [F4] to accept automatic configuration update
Setting Up the HP NetServer E 800 19 Step 7: Configuring the HP NetServer 1. Power on the HP NetServer and the monitor: ◊ Insert the HP NetServer Navigator CD-ROM in the CD-ROM drive. ◊ The server should boot from the HP NetServer Navigator CD on itsown, if not, turn the power off, wait 10 seconds a...
Page 24 - Install or Configure Tape Backup Software:
Setting Up the HP NetServer E 800 20 SCSI controller board from a third-party). You will need to use the NOS vendor’s installation process. Be sure tofirst view and print the HP-customized NOS installation instructionsand create the driver disk(s) for the NOS you are installing beforeleaving Navigat...
