HP D-04 - Manuals - manualsarea.com

Page 2 - Page

2 D04-991-2400 5/1/04 Max Pressure 2,500 psi (170 bar) Capacity @ Max Pressure rpm gpm I/min D/G-04-X 1750 2.9 11.0 D/G-04-E 1750 2.1 7.8 D/G-04-S 1750 1.6 6.1 Delivery @ Rated Pressure revs/gal 500 psi 1500 psi 2500 psi D/G-04-X 565 583 603 D/G-04-E 761 795 833 D/G-04-S 921 972 1,093 revs/liter 35 ...

Page 3 - RPM; Performance

3 D04-991-2400 5/1/04 RPM 0 NPSHr (feet of water) 1750 1 2 3 4 5 6 7 8 9 10 11 12 0 200 400 600 800 1000 1200 1400 1600 1800 D/G-04-XD/G-04-ED/G-04-S NPSHr (meters of water) 1.0 2.0 3.0 2.5 3.5 0 .5 1.5 0 RPM 0 200 400 600 800 1000 1200 1400 1600 1800 1750 500 PSI (35 bar)1500 PSI (100 bar)2500 PSI ...

Page 6 - Inlet Calculations; Acceleration Head; Supply Tank

6 D04-991-2400 5/1/04 D/G-04 Installation Inlet Calculations Acceleration Head Calculating the Acceleration Head Use the following formula to calculate acceleration head losses.Subtract this figure from the NPSHa, and compare the result tothe NPSHr of the Hydra-Cell pump. Ha = (L x V x N x C) ÷ (K x...

Page 7 - Discharge Piping; Hose and Routing

7 D04-991-2400 5/1/04 D/G-04 Installation Discharge Piping NOTE: Consult the Factory before manifolding two or morepumps together. NOTE: Single-acting pumps create a pulsing flow. Usingpulsation dampening devices in the discharge line canreduce or eliminate this. Hose and Routing Use the shortest, m...

Page 10 - Bolt Torque Specifications

10 D04-991-2400 5/1/04 D/G-04 Service (Fluid End) Bolt Torque Specifications Ref. No. D-04 G-04 1 50 ft-lbs 70 Nm 17 10 in-lbs 110 Ncm

Page 12 - Prime the Hydraulic Cells

12 D04-991-2400 5/1/04 D/G-04 Service (Fluid End) 3. Inspect and ReplaceDiaphragms (17) a. Lift a diaphragm by one edge, and turn the pump shaft until the diaphragm moves up to “top dead center”. Thiswill expose machined cross-holes in the plunger shaftbehind the diaphragm. b. I n s e r t t h e p l ...

Page 17 - Cavitation; Symptoms of Cavitation; Drop in Volume or Pressure

17 D04-991-2400 5/1/04 D/G-04 Troubleshooting Cavitation • Inadequate fluid supply because:— Inlet line collapsed or clogged — Clogged line strainer— Inlet line too small or too long — Air leak in inlet line— Worn or damaged inlet hose — Suction line too long— Too many valves and elbows in inlet lin...

Page 19 - Limited Warranty

19 D04-991-2400 5/1/04 Limited Warranty Wanner Engineering, Inc. extends to the original purchaserof equipment manufacturerd by it and bearing its name, alimited one-year warranty from the date of purchase againstdefects in material or workmanship, provided that theequipment is installed and operate...