HP BL260c - Manuals

Component identification 8 System board components Item Description 1 System board thumbscrew 2 Processor socket 2 (with blank) 3 DIMM slots (6) 4 Hard drive data connector 1 5 Hard drive data connector 2 6 Hard drive power connector 7 USB connector 8 Embedded NICs (2) 9 Mezzanine connector (Type II...

Component identification 9 Position Function Default 5 Password disabled Off 6 Reset configuration Off 7 Reserved Off 8 Reserved Off When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all system configuration settings from both CMOS and NVRAM. CA...

Operations 10 Operations Power up the server blade The enclosure initiates an automatic power-up sequence when the server blade is installed. If the default setting is changed, use one of the following methods to power up the server blade: • Use a virtual power button selection through iLO 2. • Pres...

Operations 11 Remove the server blade To remove the component: 1. Identify the proper server blade. 2. Power down the server blade (on page 10 ). 3. Remove the server blade. 4. Place the server blade on a flat, level work surface. Remove the access panel To remove the component: 1. Power down the se...

Setup 12 Setup Overview To install a server blade, complete the following steps: 1. Install and configure an HP BladeSystem c-Class enclosure. 2. Install any server blade options. 3. Install interconnect modules in the enclosure. 4. Connect the interconnect modules to the network. 5. Install a serve...

Setup 13 Interconnect bay numbering and device mapping • HP BladeSystem c7000 Enclosure • HP BladeSystem c3000 Enclosure To support network connections for specific signals, install an interconnect module in the bay corresponding to the embedded NIC or mezzanine signals. Server blade signal c7000 in...

Setup 16 4. Install the server blade. Completing the configuration To complete the server blade and HP BladeSystem configuration, see the overview card that ships with the enclosure.

Hardware options installation 17 Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury fr...

Hardware options installation 21 11. Install the hard drive cage/bezel assembly. 12. Route and connect the hard drive data and power cable to the system board. 13. Install the access panel (on page 11 ). 14. Install the server blade (" Installing a server blade " on page 14 ). 15. Determine ...

Hardware options installation 29 17. Route and connect the hard drive data and power cable to the system board. 18. Install the access panel (on page 11 ). 19. Install the server blade (" Installing a server blade " on page 14 ). Memory options You can expand server memory by installing PC2-...

Hardware options installation 30 • The following table lists all supported combinations of single-rank, dual-rank, and quad-rank DIMM configurations. "Single" indicates a slot/bank with a single-rank DIMM. "Dual" indicates a slot/bank with a dual-rank DIMM. "Quad" indicates a...

Hardware options installation 31 6. Install the access panel (on page 11 ). 7. Install the server blade (" Installing a server blade " on page 14 ). Mezzanine card option Optional mezzanine cards are classified as Type I mezzanine cards and Type II mezzanine cards. The server blade supports ...

Cabling 33 Cabling Hard drive cabling CAUTION: When routing cables, always be sure that the cables are not in a position where they can be pinched or crimped. Using the HP c-Class Blade SUV Cable The HP c-Class Blade SUV Cable enables the user to perform server blade administration, configuration, a...

Cabling 34 Numerous configurations are possible. This section offers two possible configurations. For more information, see "USB support and functionality (on page 52 )." Accessing a server blade with local KVM For this configuration, a USB hub is not necessary. To connect additional devices...

Configuration and utilities 36 Configuration and utilities Server blade deployment tools Software drivers and additional components HP offers the following additional software components for server blades: • Health and Wellness driver and IML viewer • iLO 2 Management interface driver • Rack infrast...

Configuration and utilities 37 To connect to the server blade using iLO 2, install the server blade in an enclosure. enclosure assigns an IP address to enable iLO 2 connectivity to the server blade. The c-Class tab enables you to control specific settings for the HP BladeSystem. iLO 2 also provides ...

Configuration and utilities 39 Deployment methods Four primary deployment methods are supported: IMPORTANT: To deploy a server blade without the RDP, create a bootable diskette or image of a bootable diskette. • PXE deployment (on page 39 ) • CD-ROM deployment (on page 39 ) • Diskette image deployme...

Configuration and utilities 40 Two methods are available for CD-ROM deployment: • iLO virtual CD-ROM • USB CD-ROM iLO virtual CD-ROM To deploy with a boot CD: 1. Do one of the following: o Insert the boot CD into the client PC that is using the iLO 2 Remote Console. o Use iLO 2 to create an image fi...

Configuration and utilities 41 This method implies a deployment infrastructure that may include an administrator workstation, PXE server, Microsoft® Windows® file share, or a Linux file share. For more information, refer to "Deployment infrastructure (on page 37 )." Before beginning the depl...

Configuration and utilities 42 • The FCA option is installed correctly in the server blade. Refer to the documentation that ships with the FCA option. • An FC-compatible interconnect is installed in the enclosure. Refer to the documentation that ships with the interconnect option. • The server blade...

Configuration and utilities 43 configuration process. This automated server configuration process cuts time from each server deployed, making it possible to scale server deployments to high volumes in a rapid manner. For more information, and to download the SmartStart Scripting Toolkit, refer to th...

Configuration and utilities 44 NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not automatically configure the array. You must run ORCA to configure the array settings. Drives installed Drives used RAID level 1 1 RAID 0 2 2 RAID 1 3, 4, 5, or 6 3, 4, 5, or 6 RAID 5...

Configuration and utilities 45 DIMM. DIMMs that are likely to receive a fatal/uncorrectable memory error are removed from operation automatically, resulting in less system downtime. See the server-specific user guide for DIMM population requirements. • Mirrored Memory Mode—Provides protection agains...

Configuration and utilities 46 Installing the Embedded SATA RAID driver with a USB diskette drive 1. Boot the server blade, and then press F10 to enter the ROM-Based Setup Utility (RBSU). 2. Enable the Embedded SATA RAID option under the Advanced Options section. 3. Exit RBSU. The server blade will ...

Configuration and utilities 47 Installing an operating system (Embedded SATA RAID) Embedded SATA RAID is only supported with certain operating systems. For more information about supported operating systems, see the HP website ( http://www.hp.com/go/supportos ). To install an OS, download the HP emb...

Configuration and utilities 48 6. Select Product ID . 7. Enter the product ID and press the Enter key. 8. Press the Esc key to close the menu. 9. Press the Esc key to exit RBSU. 10. Press the F10 key to confirm exiting RBSU. The server will automatically reboot. Management tools Automatic Server Rec...

Configuration and utilities 49 Erase Utility CAUTION: Perform a backup before running the System Erase Utility. The utility sets the system to its original factory state, deletes the current hardware configuration information, including array setup and disk partitioning, and erases all connected har...

Configuration and utilities 50 The Virtual Machine Management Pack provides the following functionality: • Central management and control of VMware® and Microsoft® virtual machines with physical host to virtual machine association • Easy identification of VMs or host servers reaching high CPU, memor...

Configuration and utilities 51 HP ProLiant Essentials Vulnerability and Patch Management Pack The HP ProLiant Essentials Vulnerability and Patch Management Pack software extends the functionality of HP Systems Insight Manager (HP SIM) to provide vulnerability and patch management for target systems....

Configuration and utilities 52 For more information about Insight Control Environment suites, see the HP website ( http://www.hp.com/go/ice ). HP Insight Control Linux Edition HP Insight Control Linux Edition is an all-in-one software package that provides Linux-based management and deployment capab...

Configuration and utilities 53 Diagnostic tools HP Insight Diagnostics HP Insight Diagnostics is a proactive server blade management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server blade ins...

Configuration and utilities 54 • From within HP Insight Diagnostics (on page 53 ) For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack. Remote support and analysis tools HP Instant Support Enterprise Edition ISEE is a proactive remote monitoring and diagnost...

Configuration and utilities 55 NOTE: If you are installing drivers from the SmartStart CD or the Software Maintenance CD, refer to the SmartStart website ( http://www.hp.com/servers/smartstart ) to be sure that you are using the latest version of SmartStart. For more information, refer to the docume...

Troubleshooting 57 Troubleshooting Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software mainte...

Troubleshooting 58 Important safety information Familiarize yourself with the safety information in the following sections before troubleshooting the server. Important safety information Before servicing this product, read the Important Safety Information document provided with the server. Symbols o...

Troubleshooting 59 WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module-level repair. Because of the complexity of the individual boards and subassemblies, no one should att...

Troubleshooting 60 6. Collect all tools and utilities, such as a Torx screwdriver, loopback adapters, ESD wrist strap, and software utilities, necessary to troubleshoot the problem. o You must have the appropriate Health Drivers and Management Agents installed on the server. NOTE: To verify the serv...

Troubleshooting 61 The available flowcharts include: • Start diagnosis flowchart (on page 61 ) • General diagnosis flowchart (on page 62 ) • Server blade power-on problems flowchart (on page 64 ) • POST problems flowchart (on page 66 ) • OS boot problems flowchart (on page 68 ) • Server fault indica...

Troubleshooting 62 General diagnosis flowchart The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the problem, or if the other flowcharts do not fix the problem, use the following flowchart. Item See 1 "Symptom information (on page 59 )" 2 &#...

Troubleshooting 64 Server blade power-on problems flowchart Symptoms: • The server does not power on. • The system power LED is off or amber.

Troubleshooting 66 POST problems flowchart Symptoms: • Server does not complete POST NOTE: The server has completed POST when the system attempts to access the boot device. • Server completes POST with errors Possible problems: • Improperly seated or faulty internal component • Faulty KVM device • F...

Troubleshooting 68 OS boot problems flowchart There are two ways to use SmartStart when diagnosing OS boot problems on a server blade: • Use iLO to attach virtual devices remotely to mount the SmartStart CD on the server blade. • Use an HP c-Class Blade SUV Cable and drive to connect to the server b...

Troubleshooting 70 * See the server blade OS boot problems flowchart (on page 68 ) Server fault indications flowchart Symptoms: • Server boots, but a fault event is reported by Insight Management Agents (on page 49 ) • Server boots, but the internal health LED, external health LED, or component heal...

Troubleshooting 72 POST error messages and beep codes For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers Troubleshooting Guide located on the Documentation CD or on the HP website ( http://www.hp.com/support ). WARNING: To avoid potential ...

Battery replacement 73 Battery replacement If the server blade no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithi...

Regulatory compliance notices 74 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the pro...

Regulatory compliance notices 75 energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter...

Regulatory compliance notices 76 Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouil...

Regulatory compliance notices 77 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recyc...

Regulatory compliance notices 78 Korean notice Class A equipment Class B equipment Laser compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Prod...

Regulatory compliance notices 79 WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge t...

Electrostatic discharge 80 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boar...

Specifications 81 Specifications Environmental specifications Specification Value Temperature range* Operating 10 ° C to 35 ° C (50 ° F to 95 ° F) Shipping -40 ° C to 60 ° C (-40 ° F to 140 ° F) Storage -20°C to 60°C (-4°F to 140°F) Maximum wet bulb temperature 30 ° C (86 ° F) Relative humidity (non...

Technical support 82 Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number • Product identification number • Applicable error mess...

Technical support 84 l'ensemble des frais d'expédition et de retour, et détermine la société de courses ou le transporteur à utiliser. Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez...

Technical support 85 lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen. HINWEIS : Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Se...

Technical support 86 de envío. Si no enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que s...

Acronyms and abbreviations 90 Acronyms and abbreviations ABEND abnormal end AMP Advanced Memory Protection ASR Automatic Server Recovery CSR Customer Self Repair DHCP Dynamic Host Configuration Protocol DRAM dynamic random access memory HP SIM HP Systems Insight Manager iLO 2 Integrated Lights-Out 2...

Acronyms and abbreviations 92 V2V virtual to virtual VCA Version Control Agent VM Virtual Machine WEBES Web-Based Enterprise Service WfM Wired for Management

Index 93 A access panel 11 additional information 57 Advanced ECC memory 29, 44 Advanced ECC support 29 ASR (Automatic Server Recovery) 48 authorized reseller 82 auto-configuration process 43 Automatic Server Recovery (ASR) 48 Autorun menu 42 B Basic Input/Output System (BIOS) 44, 48 batteries, repl...