Page 2 - Notice
2 Notice The information contained in this document is subject to change withoutnotice. Hewlett-Packard makes no warranty of any kind with regard to thismaterial, including, but not limited to, the implied warranties ofmerchantability or fitness for a particular purpose. Hewlett-Packardshall not be ...
Page 3 - Contents; HP-PB 100VG-AnyLAN Network Adapter Installation at a Glance 9
Contents 3 HP-PB 100VG-AnyLAN Network Adapter Installation at a Glance 9 Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Product Contents . . ....
Page 5 - Figures
Figures 5 Figure 1-1 . Address Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Figure 1-2 . Inserting and Securing Adapter . . . . . . . . . . . . . . . . . . . . . .19 Figure 1-3 . Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20...
Page 7 - Tables
Tables 7 Table 1-1. LED Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Table 2-1. Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Table 2-2. 100VG Network Adapter Technical Specifications . . . . . . . . .30
Page 11 - In This Book
11 In This Book This book is the installation and service manual for the HP-PB100VG-AnyLAN Network Adapter that connects an HP 3000 computerusing the HP-PB backplane to a 100VG-AnyLAN network. The installation procedure section contains the installation instructions.It explains in detail the steps n...
Page 13 - Installation Procedure
13 1 Installation Procedure This section contains installation instructions for the HP-PB100VG-AnyLAN Network Adapter. The instructions are organized intosix primary steps listed below. Each step is described in detail in thissection. If the adapter has already been installed at the factory, you may...
Page 14 - Prepare to Install the Adapter; Observe Antistatic Precautions; Verify Product Contents
14 Chapter 1 Installation Procedure 1. Prepare to Install the Adapter 1. Prepare to Install the Adapter Before installing the adapter, you should perform the following steps: 1. Observe antistatic precautions. 2. Verify product contents. 3. Record adapter identification information. 4. Gather tools ...
Page 15 - Record Adapter Information
Chapter 1 15 Installation Procedure 1. Prepare to Install the Adapter Record Adapter Information Record the relevant information from the card here for future reference.If your adapter requires service in the future this information will beneeded by HP service personnel. This information is provided...
Page 16 - Gather Tools and Accessories
16 Chapter 1 Installation Procedure 1. Prepare to Install the Adapter Gather Tools and Accessories Check the hardware installation manual of your computer model forspecial tools and accessories required to access the I/O adapter slot(s).The following common tools are helpful: • screwdrivers necessar...
Page 18 - Install the Adapter; b. Select an available slot
18 Chapter 1 Installation Procedure 3. Install the Adapter 3. Install the Adapter To install the adapter in the host computer, perform the following steps: a. Access the adapter slot(s). b. Select an available adapter slot. c. Insert the adapter into the slot. d. Switch on the power to the computer....
Page 20 - Attach the Adapter to the Network
20 Chapter 1 Installation Procedure 4. Attach the Adapter to the Network 4. Attach the Adapter to the Network Use the RJ-45 connector for connecting a UTP category 3 or 5 cable(not supplied) to a 100VG-AnyLAN hub or 10Base-T hub/switch. Refer toFigure 1-3.. Figure 1-3 Port Connection Attach the cabl...
Page 21 - Configure the Adapter into the System
Chapter 1 21 Installation Procedure 5. Configure the Adapter into the System 5. Configure the Adapter into the System On MPE systems you will need to configure the adapter into the system.In particular you must specify link speed and duplex settings to matchthose of the network hub/switch port to wh...
Page 23 - Service Information
23 2 Service Information This section provides the following service information: • Field Replaceable Units • Troubleshooting Tools • Removal/Replacement Instructions • Reshipment Guidelines • Technical Specifications
Page 24 - Field Replaceable Units; Exchange Assembly
24 Chapter 2 Service Information Field Replaceable Units Field Replaceable Units Field Replaceable Units (FRUs) are assemblies or components that areauthorized for field replacement. There are no FRUs on this adapter. If there should be a problem theentire adapter is replaceable. Exchange Assembly T...
Page 25 - Troubleshooting Tools; Card LEDs
Chapter 2 25 Service Information Troubleshooting Tools Troubleshooting Tools Troubleshooting tools are used to identify faulty adapters. For thisproduct, the following tools are available: • troubleshooting checklist (see Table 2-1) • VGPBA online diagnostic (has online help) Card LEDs The 6 LEDs on...
Page 27 - Removal/Replacement Instructions
Chapter 2 27 Service Information Removal/Replacement Instructions Removal/Replacement Instructions This section describes removal and replacement for theHP-PB 100VG-AnyLAN Network Adapter. WARNING Unless otherwise noted in your system manuals, removal of thenetwork adapter should only be done with p...
Page 28 - Removal/Replacement of the Adapter
28 Chapter 2 Service Information Removal/Replacement Instructions Removal/Replacement of the Adapter For adapter removal, follow the procedures below: 1. Before removing the card, ensure that the operating system is shut down and power to the host computer is switched off. Consult yourcomputer docum...
Page 29 - Reshipment Guidelines
Chapter 2 29 Service Information Reshipment Guidelines Reshipment Guidelines If any item of the product is to be returned to Hewlett-Packard for anyreason, contact your HP Sales and Support Office to coordinate thereturn. When returning the item, attach a tag that identifies the owner andindicates t...
Page 30 - Technical Specifications
30 Chapter 2 Service Information Technical Specifications Technical Specifications The network adapter technical specifications are provided in Table 2-2. Table 2-2 100VG Network Adapter Technical Specifications Specifications Safety • UL 1950, 2nd Edition • CSA 22.2 No 950, 2nd Edition • IEC 950 (1...
Page 31 - Declaration of Conformity
Chapter 2 31 Service Information Declaration of Conformity Declaration of Conformity A declalaration of conformity is shown in . Figure 2-1 Declaration of Conformity
Page 33 - Numbers
Glossary 33 Glossary Numbers 100VG-AnyLAN Refers to the100Mbit/s network technology overvoice grade cable that iscompatible with the IEEE 802.12standard. This technologyguarantees access to any end nodethat request to transmit, whichensuring priority access to endnodes that require consistent,contin...
