Page 2 - Legal Notices
2 Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, theimplied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be h...
Page 3 - Step 1: Access the system card bay; Hardware and Software Installation Procedure; sync; Step 2: Install the card
Hardware and Software Installation Procedure Step 1: Access the system card bay 3 Hardware and Software Installation Procedure These instructions apply to AB465A PCI-X 2-Port 2 Gigabit Fibre Channel and 2-Port Gigabit Ethernetcombination cards which can operate on HP-UX 11i v 1.0 of December 2004 or...
Page 4 - Step 4: Connect the fibre channel devices; echo; Table 1; HP-UX 1000Base-T Supported Configurations; Link Partner; AUTO
Hardware and Software Installation Procedure Step 4: Connect the fibre channel devices 4 • Attach the free end of the LAN cable to any unused port on the switch. The Base-T connections on thecard operate at 10 or 100 Mbit/s in either full- or half-duplex modes and at 1000 Mbit/s only in full-duplexm...
Page 5 - swinstall; Step 7: Configure the card using SAM; ioscan
Hardware and Software Installation Procedure Step 6: Install the latest software. 5 • Check the Release Notes for GigEther-01 and FibrChanl-01 to see if you need to install any appropriatepatches for your system. Release Notes are available on the Web at http://docs.hp.com under Networkingand Commun...
Page 6 - Step 8: Verify the fibre channel installation; HP Fibre Channel Mass Storage Adapters Support Guide; Step 9: Verify the LAN installation; ping
Hardware and Software Installation Procedure Step 8: Verify the fibre channel installation 6 Step 8: Verify the fibre channel installation • To verify that the fc driver appears for each installed card, enter: ioscan -fk The ioscan output might look like the following: Class I H/W Path Driver S/W St...
Page 7 - Optional Step: Configure Jumbo Frames Size; LAN; Ethernet Support Guide
Hardware and Software Installation Procedure Optional Step: Configure Jumbo Frames Size (Jumbo frames are supported only at 1000 Mbit/s) 7 • Installation is complete when you have successfully run linkloop , ping and netstat . To configure remote systems, see the Ethernet Support Guide available on ...
Page 8 - lanadmin; For Further Information; fcd; Maintenance and troubleshooting information
Hardware and Software Installation Procedure For Further Information 8 An alternative way to temporarily configure jumbo frame size is to enter: lanadmin -M mtu_size PPA_number . Using lanadmin is temporary because it will not preserve your settings across reboots. The PPA_number is the one we obtai...
Page 9 - Network Configuration Worksheet; Using lanadmin will not preserve your settings across reboots.; Table 2
Hardware and Software Installation Procedure Network Configuration Worksheet 9 Network Configuration Worksheet Fill out one worksheet for the networking data of each LAN port on the combination card you are installing. Note 1 : To configure values permanently, edit the configuration files using SAM ...
Page 10 - Cable Specifications; Operating Distance for 1000Base-T
Hardware and Software Installation Procedure Cable Specifications 10 Note 3 : The valid MTU size for normal frames using the igelan driver on HP-UX 11i v 1.0 or v 2.0 is 1500 bytes. For Jumbo Frames, the valid MTU size on HP-UX 11i v 1.0 is 9000 , and for HP-UX 11i v 2.0, it is anumber in the range ...
Page 11 - Figure 1; Fibre Channel Connectors
Hardware and Software Installation Procedure 11 Figure 1 AB465A PCI-X 2-Port 2Gb FC/ 2-Port 1000B-T Combination Card (Duplex LC) Fibre Channel Connectors PCI-X 133 MHz 1000Base-T Connectors (RJ-45) Speed LEDS (Port 2) 1Gb 2Gb Speed LEDS (Port 1) 2Gb 1Gb Speed LEDsOff = 10 Mbit/s Green = 100 Mbit/sYe...
Page 12 - Features; not; Jumbo Frames; VLANs; SAM; fcmsutil
Hardware and Software Installation Procedure Features 12 Features The AB465A PCI-X Combination cards have the following features: • PCI-X 133 MHz capable card. It can operate at 32-bit or 64-bit compatible modes and is supported in the following frequencies: PCI 66, PCI-X 66, and PCI-X 133. Best per...
Page 13 - Interoperability: Supported Systems; The combination card is supported in the HP Integrity (Itanium; Table 3
Hardware and Software Installation Procedure Interoperability: Supported Systems 13 Interoperability: Supported Systems Supported Systems The combination card is supported in the HP Integrity (Itanium or Itanium 2-based) systems specified in Table 3. The combination card is supported in the HP 9...
Page 14 - Card Physical and Environmental Specifications; Physical Specifications
Card Physical and Environmental Specs and Regulatory Information Card Physical and Environmental Specifications 14 Card Physical and EnvironmentalSpecs and Regulatory Information Card Physical and Environmental Specifications Following are the product physical and environmental specifications of the...
Page 15 - Operating Altitude
Card Physical and Environmental Specs and Regulatory Information Card Physical and Environmental Specifications 15 Electromagnetic Compatibility This document contains regulatory statements for the United States and the European community. Operating Altitude 3,000 meters (9900) ft Non-operating Alti...
Page 16 - WARNING; Canada; NOTE
Card Physical and Environmental Specs and Regulatory Information FCC Statement (For U.S.A.) 16 FCC Statement (For U.S.A.) Federal Communications Commission Radio Frequency Interference Statement WARNING This device complies with Part 15 of the FCC rules. Operation is subject to thefollowing two cond...
Page 17 - Laser Safety Statements; CAUTION
Card Physical and Environmental Specs and Regulatory Information Laser Safety Statements 17 Laser Safety Statements Laser Safety Statements - U.S. FDA/CDRH - Optical (laser) Transceiver CAUTION The optical transceiver provided on the network interface card contains a laser system and isclassified as...
