Page 5 - Quick Installation 3; HP JetDirect Print Servers; for Fast Ethernet
Quick Installation 3 HP JetDirect Print Servers HP J4100A for Fast Ethernet and IEEE 802.3u (10/100Base-TX, 10Base2) networks. An RJ-45 connector supports 10/100 Mbps network connections using unshielded twisted-pair cable. (For 100Base-TX networks, use Category 5 cable.) The BNC connector supports ...
Page 6 - Quick Installation; NOTE; See chapter 2 for detailed information.; If you have a Token Ring card,; Print a test page or configuration plot. For instructions,; Turn off your printer and insert the card.
4 Quick Installation Quick Installation NOTE See chapter 2 for detailed information. 1. If you have a Token Ring card, Set the network Data-Rate switch to 16 Mbps (default) or 4 Mbps depending on your network. If you don't know the network data rate, ask your network administrator. 2. Before install...
Page 7 - Quick Installation 5; Verify that the card was installed correctly.; HP JetDirect Print Server; Configure the card for network operation.
Quick Installation 5 4. Verify that the card was installed correctly. Print another test page (or configuration plot) and verify that the “I/O CARD READY” message appears. On the test page, the location of the “I/O CARD READY” message depends on your printer model. NOTE If other messages appear, see...
Page 8 - Quick Installation
Page 9 - Contents; Task 1. If you have a Token Ring card, set the
7 Contents Contents Quick Installation 1 The HP JetDirect Print Server Card Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1The HP JetDirect Print Server Cards at a Glance . . . . . . . 1-2Supported Networks . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 10 - Configuring the Timeout for End-of-Job Sensing for the; A Specifications and Regulatory Statements
8 4 Using the Control Panel To Configure HP JetDirect Cards in Large-Format Printers Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Supported Network Protocols . . . . . . . . . . . . . . . . . . . . . . . . 4-2Configuring Novell NetWare Frame Types . . ....
Page 11 - The HP JetDirect Print Server Card 1-1; Introduction; The HP JetDirect Print Server Card; HP CopyJet and CopyJet M color printer-copier
The HP JetDirect Print Server Card 1-1 1 Introduction 1 The HP JetDirect Print Server Card Introduction The HP JetDirect print server is a card that is installed in the modular input/output (MIO) slot of a printer and allows the printer to be connected directly to a network instead of a single PC. W...
Page 12 - -2 The HP JetDirect Print Server Card
1-2 The HP JetDirect Print Server Card The HP JetDirect Print Server Cards at a Glance J4100A J4105A J4106A Network Types Network Connections Supported Ethernet, IEEE 802.3 (10/100Base-TX, 10Base2) RJ-45 (unshielded twisted-pair cable), BNC (thin Ethernet coaxial cable) Network Types Network Connect...
Page 13 - The HP JetDirect Print Server Card 1-3; Supported Networks; EtherTalk
The HP JetDirect Print Server Card 1-3 1 Introduction Supported Networks Supported Network Protocols Supported Networks 1 Applicable Products IPX/SPX and compatible Novell NetWareMicrosoft Windows 95/98/NT/2000 J4100AJ4105AJ4106A EtherTalk AppleTalk J4100AJ4106A DLC/LLC Microsoft Windows NTAr tisoft...
Page 14 - -4 The HP JetDirect Print Server Card; What You Need for Installation; CAUTION
1-4 The HP JetDirect Print Server Card What You Need for Installation • The appropriate HP JetDirect print server, documentation, and software. • A static-safe environment for handling the card. A grounding wrist strap or similar device is recommended. • Appropriate network cables and connectors for...
Page 15 - Installing the HP JetDirect Print Server Card 2-1; Installation
Installing the HP JetDirect Print Server Card 2-1 2 Installation 2 Installing the HP JetDirect Print Server Card Task 1. If you have a Token Ring card, set the Data-Rate switch (if necessary) Before installing a Token Ring card, you must set the data-rate switch to either 4 Mbit/second or 16 Mbit/se...
Page 16 - -2 Installing the HP JetDirect Print Server Card; TEST MENU; Control Panel for the HP LaserJet 5, 5M, 5N
2-2 Installing the HP JetDirect Print Server Card Task 2. Before installing the card, verify the printer works The following pages show instructions for printing a self-test page or configuration plot to verify the printer is operating correctly. Locate and follow the instructions for your specific ...
Page 17 - Installing the HP JetDirect Print Server Card 2-3
Installing the HP JetDirect Print Server Card 2-3 2 Installation HP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers 1. Turn on the printer and wait until a ready message is displayed. 2. Press [Menus] repeatedly until TEST MENU appears. 3. Press [Items] until PCL CONFIGURATION PAGE appears. 4. Pre...
Page 18 - -4 Installing the HP JetDirect Print Server Card
2-4 Installing the HP JetDirect Print Server Card HP Color LaserJet and Color LaserJet 5, 5M printers 1. Turn on the printer and wait until a ready message is displayed. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until the following ...
Page 19 - Installing the HP JetDirect Print Server Card 2-5
Installing the HP JetDirect Print Server Card 2-5 2 Installation HP LaserJet 4, 4M, 4 Plus, and 4M Plus printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until TEST MENU...
Page 20 - -6 Installing the HP JetDirect Print Server Card; HP LaserJet 4Si and 4Si MX printers; Control Panel for HP LaserJet 4Si and 4Si MX
2-6 Installing the HP JetDirect Print Server Card HP LaserJet 4Si and 4Si MX printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until TEST MENU appears. 4. Press [Item] r...
Page 21 - Installing the HP JetDirect Print Server Card 2-7; HP LaserJet 4V and 4MV printers; Control Panel for HP LaserJet 4V and 4MV
Installing the HP JetDirect Print Server Card 2-7 2 Installation HP LaserJet 4V and 4MV printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switch the printer offline by pressing [On Line] to turn off the On Line light. 3. Press [Menu] repeatedly until TEST MENU appears. 4. Pre...
Page 22 - -8 Installing the HP JetDirect Print Server Card; READY
2-8 Installing the HP JetDirect Print Server Card HP 2500C/CM Professional Series and HP DesignJet ColorPro GA Printers 1. Turn on the printer and wait for READY to appear in the display panel. 2. Press [Menu] until SELF TEST MENU appears. 3. Press [Item] to display PRINT DIAGNOSTIC PAGE . 4. Press ...
Page 23 - Installing the HP JetDirect Print Server Card 2-9; Turn on the printer and wait until the Ready light is lit.
Installing the HP JetDirect Print Server Card 2-9 2 Installation HP DeskJet 1600C, 1600CM, and 1600CN printers 1. Turn on the printer. 2. Press the blue button. A self-test page will print. HP DeskJet 1200C and 1200 C/PS printers 1. Turn on the printer and wait until the Ready light is lit. 2. Switc...
Page 24 - -10 Installing the HP JetDirect Print Server Card; HP DesignJet 600 Series large-format printers; STATUS
2-10 Installing the HP JetDirect Print Server Card HP DesignJet 600 Series large-format printers 1. Turn on the printer and wait until the printer displays STATUS Ready to plot . 2. Press [Enter] . FULL MENUS Plot Mgmt → appears. 3. Press ↓ until FULL MENUS Utilities appears. 4. Press [Enter] again....
Page 25 - Installing the HP JetDirect Print Server Card 2-11; STATUS Ready
Installing the HP JetDirect Print Server Card 2-11 2 Installation HP DesignJet 700, 750C, 750C Plus, 755CM, 2000CP, 2500CP, 3000CP, 3500CP large-format printers To print a DesignJet configuration page: 1. Turn on the printer and wait until STATUS Ready appears. 2. Press the two arrow keys simultaneo...
Page 26 - -12 Installing the HP JetDirect Print Server Card; HP CopyJet and CopyJet M color printer-copiers; Press the; Control Panel for HP CopyJet and CopyJet M printer-copiers
2-12 Installing the HP JetDirect Print Server Card HP CopyJet and CopyJet M color printer-copiers 1. Turn on the printer. 2. Press the [Test Menu] button. The control panel display shows - = Test page+ = PCL fonts 3. Press [-] to print the Test Page. Control Panel for HP CopyJet and CopyJet M printe...
Page 27 - Installing the HP JetDirect Print Server Card 2-13; Turn off the printer and unplug the power cord.
Installing the HP JetDirect Print Server Card 2-13 2 Installation Task 3. Insert the HP JetDirect print server card into the printer Locate the instructions for installing the card into your specific printer. To prevent electrostatic discharge (ESD) damage when installing the card, maintain frequent...
Page 28 - -14 Installing the HP JetDirect Print Server Card; If the slot has a cover plate, remove it.; one
2-14 Installing the HP JetDirect Print Server Card 3. If the slot has a cover plate, remove it. 4. Insert the card. Align the card with the guide rails in the printer. 5. Press the card into the slot until firmly seated and tighten each thumbscrew a little at a time, alternating between each side un...
Page 29 - Installing the HP JetDirect Print Server Card 2-15
Installing the HP JetDirect Print Server Card 2-15 2 Installation To install the card into the HP LaserJet 4V and 4MV printers 1. Turn off the printer and unplug the power cord. 2. Locate the HP modular I/O (MIO) slot at the back of the printer (see the figure below). 3. If the slot has a cover plat...
Page 30 - -16 Installing the HP JetDirect Print Server Card; Components face right for HP LaserJet 5, 5M, 5N
2-16 Installing the HP JetDirect Print Server Card To install the card into the HP LaserJet 5, 5M, or 5N printers 1. Turn off the printer and unplug the power cord. 2. Locate the HP Modular Input/Output (MIO) slot at the back of the printer (see the figure below). 3. If the slot has a cover plate, r...
Page 31 - Installing the HP JetDirect Print Server Card 2-17; Note the following restrictions:; in the upper slot of an HP LaserJet
Installing the HP JetDirect Print Server Card 2-17 2 Installation The HP LaserJet 4Si Series and 5Si Series Printers Have Two Card Slots The HP LaserJet 4Si, 4Si MX, 5Si, 5Si MX, 5Si NX, and 5Si Mopier printers have two HP modular input/output (MIO) slots that enable you to run more than one type of...
Page 32 - -18 Installing the HP JetDirect Print Server Card; To install a card into the; lower slot; either slot; of the; Components face left in HP LaserJet 4Si Series
2-18 Installing the HP JetDirect Print Server Card To install a card into the lower slot of the HP LaserJet 4Si Series, and either slot of the 5Si Series printers 1. Turn off the printer and unplug the power cord. 2. Locate the HP modular I/O (MIO) slots at the back of the printer. Components face l...
Page 33 - Installing the HP JetDirect Print Server Card 2-19; Press the card into the slot until the card is firmly seated.
Installing the HP JetDirect Print Server Card 2-19 2 Installation 3. Remove the cover plate. (Remember: use the lower slot for the 4Si or 4Si MX.) 4. Insert the card. Align the card with the guide rails in the printer. 5. Press the card into the slot until the card is firmly seated. 6. Tighten each ...
Page 34 - -20 Installing the HP JetDirect Print Server Card; Remove card from lower MIO slot
2-20 Installing the HP JetDirect Print Server Card To install a card into the upper MIO slot of the HP LaserJet 4Si and 4Si MX printers NOTE To use the upper slot of an HP LaserJet 4Si or 4Si MX printer, you must assemble two cards together and insert them both into the printer at the same time. To ...
Page 35 - Installing the HP JetDirect Print Server Card 2-21; • If your HP JetDirect card is a Token Ring card, also remove; Remove faceplate from card
Installing the HP JetDirect Print Server Card 2-21 2 Installation 4. For the HP JetDirect card that will be installed into the upper slot, remove the front plate by removing the two side screws (A). • If your HP JetDirect card is a Token Ring card, also remove the mounting screws (B) from the front ...
Page 36 - -22 Installing the HP JetDirect Print Server Card
2-22 Installing the HP JetDirect Print Server Card 6. Compare the HP JetDirect card’s front plate with the custom cover plate. Peel off the appropriate part of the label on the customized cover plate to match the holes punched out on the HP JetDirect card’s front plate: • If you are installing an HP...
Page 37 - Installing the HP JetDirect Print Server Card 2-23; Connect cards with customized plate at right
Installing the HP JetDirect Print Server Card 2-23 2 Installation 8. With the components facing up, assemble the two cards together. The card that will be installed into the upper slot (with custom cover plate) will be to the right. Secure the cards by tightening the spring-loaded thumbscrews (C). 9...
Page 38 - -24 Installing the HP JetDirect Print Server Card; With the components facing the left edge of the printer, slide; Secure the assembly to the printer by tightening the remaining; Insertion of two cards into HP LaserJet 4Si/4SiMX
2-24 Installing the HP JetDirect Print Server Card 10. With the components facing the left edge of the printer, slide the card assembly into the printer. Align the top and bottom of the assembly with the top and bottom guide rails located inside the printer. Press the cards into the slot until the c...
Page 39 - Installing the HP JetDirect Print Server Card 2-25
Installing the HP JetDirect Print Server Card 2-25 2 Installation NOTE For the HP J4100A JetDirect card (RJ-45 and BNC), you can connect to one of the Ethernet ports (only one Ethernet port is active at a time). For the HP J4105A JetDirect card (RJ-45 and DB9, you can connect to only one Token Ring ...
Page 40 - -26 Installing the HP JetDirect Print Server Card
2-26 Installing the HP JetDirect Print Server Card NOTE For the HP J4100A JetDirect card (RJ-45 and BNC), you can connect to one of the Ethernet ports (only one Ethernet port is active at a time). For the HP J4105A JetDirect card (RJ-45 and DB9), you can connect to only one Token Ring port. 7. Conne...
Page 41 - Installing the HP JetDirect Print Server Card 2-27; Connect the network cable to the card.
Installing the HP JetDirect Print Server Card 2-27 2 Installation 4. Insert the card. Align the card with the guide rails in the printer. 5. Press the card into the slot until firmly seated and tighten each thumbscrew a little at a time, alternating between each side until both screws are secure. 6....
Page 42 - -28 Installing the HP JetDirect Print Server Card; Turn off the printer but
2-28 Installing the HP JetDirect Print Server Card To install the card into the HP DesignJet 600 Series, 700 Series, 2000/2500/3000/3500 Series large-format printers 1. Turn off the printer but leave the power cord plugged in . 2. Locate the HP modular I/O (MIO) slot located at the back of the print...
Page 43 - Installing the HP JetDirect Print Server Card 2-29
Installing the HP JetDirect Print Server Card 2-29 2 Installation 3. If the slot has a cover plate, remove it. 4. Insert the card. Align the card with the guide rails in the printer. 5. Press the card into the slot until the card is firmly seated. 6. Tighten each thumbscrew a little at a time, alter...
Page 44 - -30 Installing the HP JetDirect Print Server Card
2-30 Installing the HP JetDirect Print Server Card To install the card into the HP CopyJet and CopyJet M color printer-copiers 1. Turn off the printer and unplug the power cord. 2. Locate the HP modular I/O (MIO) slot at the back of the printer (see the figure below). 3. If the slot has a cover plat...
Page 45 - Installing the HP JetDirect Print Server Card 2-31
Installing the HP JetDirect Print Server Card 2-31 2 Installation Task 4. Verify the card was installed correctly 1. Print a new self-test page or configuration page. 2. Using the diagram on the following page as a guide, locate the phrase “I/O CARD READY” on the self-test page. The I/O CARD READY m...
Page 46 - -32 Installing the HP JetDirect Print Server Card; Administrators Guide
2-32 Installing the HP JetDirect Print Server Card 3. For more information about this section of the self-test page, see your HP JetDirect Administrators Guide on the HP JetDirect CD-ROM. 4. If the I/O CARD READY message appears, the card has been installed successfully. See “What To Do Next”. If th...
Page 47 - Installing the HP JetDirect Print Server Card 2-33; HP JetDirect 400N Quick Setup Guide; What To Do Next; HP JetDirect Quick Setup Guide
Installing the HP JetDirect Print Server Card 2-33 2 Installation NOTE For HP J4100A 10/100Base-TX cards, see appendix B in this manual for special troubleshooting information. If the message still does not appear, contact HP Customer Care (see the HP JetDirect 400N Quick Setup Guide for phone numbe...
Page 48 - -34 Installing the HP JetDirect Print Server Card
Page 49 - Using the Control Panel for Printers 3-1; Printer Control; HP DesignJet ColorPro GA printer
Using the Control Panel for Printers 3-1 3 Printer Control Panel 3 Using the Control Panel To Configure HP JetDirect Cards in Printers Introduction If you have an HP DesignJet large-format printer (except DesignJet ColorPro GA), go to Chapter 4. The printers listed below have control panels that let...
Page 50 - -2 Using the Control Panel for Printers; Enabling and Disabling Network Protocols; To restore configuration default values; on some printers) as you turn the printer
3-2 Using the Control Panel for Printers Enabling and Disabling Network Protocols When you first install the card from the factory, all supported network protocols are enabled (or turned on) when you turn the printer on. The card provides automatic network switching between network protocols for pri...
Page 51 - Using the Control Panel for Printers 3-3; To enable or disable network protocols; does not
Using the Control Panel for Printers 3-3 3 Printer Control Panel To enable or disable network protocols NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the “HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel” instructions at the end of this chapt...
Page 52 - -4 Using the Control Panel for Printers; Configuring Novell NetWare Frame Types; Frame Type
3-4 Using the Control Panel for Printers 8. Press [Item] to continue to the next protocol. Example: To enable the DLC/LLC protocol, press [Item] until the control panel displays either DLC/LLC=ON* or DLC/LLC=OFF* . If DLC/LLC=ON* is displayed, press [Item] to retain that protocol and continue to the...
Page 53 - Using the Control Panel for Printers 3-5; To configure a NetWare frame type; Proceed to Step 4
Using the Control Panel for Printers 3-5 3 Printer Control Panel Novell NetWare Frame Types on an HP JetDirect Token Ring Card To configure a NetWare frame type NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the “HP 2500C/CM Professional Series and DesignJet ColorPr...
Page 54 - -6 Using the Control Panel for Printers
3-6 Using the Control Panel for Printers 3. Press [Item] until CFG NETWORK=NO* appears. 4. Change the message to CFG NETWORK=YES* using the following buttons: 5. Press [Item] until CFG IPX/SPX=NO* appears. 6. Change this to CFG IPX/SPX=YES* by pressing [+] , and then pressing [Select] or [Enter] dep...
Page 55 - Using the Control Panel for Printers 3-7; Single; To configure NetWare source routing; AUX IO MENU
Using the Control Panel for Printers 3-7 3 Printer Control Panel Configuring Novell NetWare Source Routing (Token Ring Cards Only) You can select the method for Novell NetWare Token Ring source routing from the control panel. The possible routing methods are: • AUTO (default): Source routing is enab...
Page 56 - -8 Using the Control Panel for Printers; MIO MENU 1
3-8 Using the Control Panel for Printers 3. Press [Item] until CFG NETWORK=NO* appears. 4. Change the message to CFG NETWORK=YES* using the following buttons: 5. Press [Item] until CFG IPX/SPX=NO* appears. 6. Change this to CFG IPX/SPX=YES* by pressing [+] , and then pressing [Select] or [Enter] dep...
Page 57 - Using the Control Panel for Printers 3-9; Configuring TCP/IP Parameters; or
Using the Control Panel for Printers 3-9 3 Printer Control Panel Configuring TCP/IP Parameters Using the control panel of your printer, you can manually configure these TCP/IP parameters: • You can configure BOOTP, which automatically downloads configuration data over the network (this is the defaul...
Page 58 - -10 Using the Control Panel for Printers; To configure TCP/IP parameters
3-10 Using the Control Panel for Printers To configure TCP/IP parameters NOTE For HP 2500C/CM Professional Series and DesignJet ColorPro GA printers, see the “HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel” instructions at the end of this chapter. If you have not already don...
Page 59 - Using the Control Panel for Printers 3-11
Using the Control Panel for Printers 3-11 3 Printer Control Panel 6. Change this to CFG TCP/IP=YES* by pressing [+] , and then pressing [Select] or [Enter] depending on your printer model. 7. Press [Item] until BOOTP=YES* or BOOTP=NO* appears. • The asterisk ( * ) indicates the active selection. • T...
Page 60 - -12 Using the Control Panel for Printers; To configure EtherTalk parameters
3-12 Using the Control Panel for Printers Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) You can configure Apple EtherTalk parameters if the Apple EtherTalk protocol is enabled ( ETALK=ON* ), and the PostScript printer language is enabled. To ensure the PostScript printer languag...
Page 61 - Using the Control Panel for Printers 3-13
Using the Control Panel for Printers 3-13 3 Printer Control Panel 4. Change the message to CFG NETWORK=YES* using the following buttons: 5. Press [Item] until CFG ETALK=NO* appears. 6. Change this to CFG ETALK=YES* by pressing [+] , and then pressing [Select] or [Enter] depending on your printer mod...
Page 62 - -14 Using the Control Panel for Printers
3-14 Using the Control Panel for Printers Configuring the Timeout for End-of-Job Sensing When installed in an HP LaserJet 4 or 4M printer, the HP JetDirect card provides a Job Timeout parameter. For networks with multiple network protocols, the Job Timeout parameter specifies the time that the HP Je...
Page 63 - Using the Control Panel for Printers 3-15; MIO MENU
Using the Control Panel for Printers 3-15 3 Printer Control Panel HP 2500C/CM Professional Series and DesignJet ColorPro GA Control Panel To enable or disable network protocols 1. Take the printer offline by pressing the online/offline button . 2. Press [Menu] repeatedly until MIO MENU appears. 3. P...
Page 64 - -16 Using the Control Panel for Printers; does
3-16 Using the Control Panel for Printers To configure a NetWare frame type If you have not already done so, enable the IPX/SPX protocol ( IPX/ SPX ON ) by following the instructions above. 1. Take the printer offline by press the online/offline button . 2. Press [Menu] repeatedly until MIO MENU app...
Page 65 - Using the Control Panel for Printers 3-17
Using the Control Panel for Printers 3-17 3 Printer Control Panel 4. Press [Select] . CFG NETWORK NO appears. This message does not mean that you must reconfigure your protocol. It means only that you do not intend to access the network configuration menus. 5. Press [Value] to display CFG NETWORK YE...
Page 66 - -18 Using the Control Panel for Printers; BOOTP YES
3-18 Using the Control Panel for Printers 7. Change this to CFG TCP/IP YES by pressing [Value] . Then press [Select] . 8. Press [Item] until BOOTP YES or BOOTP NO appears. 9. To change the BOOTP setting, press [Value] . Then press [Select] . • If BOOTP YES is set, the printer is configured to retrie...
Page 67 - Using the Control Panel for Printers 3-19
Using the Control Panel for Printers 3-19 3 Printer Control Panel To configure EtherTalk parameters To ensure the PostScript printer language is enabled, check the CONFIGURATION MENU . PERSONALITY=PS or PERSONALITY=AUTO should be set. If you haven’t already done so, enable EtherTalk ( ETALK ON ) by ...
Page 68 - -20 Using the Control Panel for Printers
Page 69 - Control Panel for Large-Format Printers 4-1; HP DesignJet; You can use the printer control panel to do the following:
Control Panel for Large-Format Printers 4-1 4 HP DesignJet Control Panel 4 Using the Control Panel To Configure HP JetDirect Cards in Large-Format Printers Introduction If you have an HP DesignJet printer listed below, you can manually configure certain network parameters using the printer control p...
Page 70 - -2 Control Panel for Large-Format Printers; Supported Network Protocols
4-2 Control Panel for Large-Format Printers Once you have configured these parameters using the control panel, you still need to install the appropriate print server software to complete the configuration process. Refer to your HP JetDirect software installation guide for instructions. Supported Net...
Page 71 - Control Panel for Large-Format Printers 4-3
Control Panel for Large-Format Printers 4-3 4 HP DesignJet Control Panel To enable or disable network protocols on the DesignJet 600 Series printers 1. Turn on the printer. 2. Verify that the printer displays STATUS and Ready to plot . 3. Press [Enter] until MENUS ( FULL MENUS on the 650C printer) a...
Page 72 - -4 Control Panel for Large-Format Printers
4-4 Control Panel for Large-Format Printers NOTE You will see CFG NETWORK=NO whenever you enter the JetDirect configuration menu. The message only indicates that you do not intend to access the configuration menu. It does not mean that you must reconfigure your protocol. To continue manually configu...
Page 73 - Control Panel for Large-Format Printers 4-5; YES
Control Panel for Large-Format Printers 4-5 4 HP DesignJet Control Panel 6. Press ↓ to change NO* to YES , then press [Enter] to display CFG NETWORK=YES . 7. At the CFG NETWORK=YES message, press ↑ repeatedly to scroll through the configuration options. a. To change a network protocol setting (enabl...
Page 74 - -6 Control Panel for Large-Format Printers
4-6 Control Panel for Large-Format Printers Configuring Novell NetWare Frame Types You can set the NetWare frame types if the NetWare protocol is enabled ( NETWORK=NOVELL → or NETWORK=AUTO → was displayed on your control panel). You can configure one of the following frame-type settings: Novell NetW...
Page 75 - Control Panel for Large-Format Printers 4-7; For the 600 Series Printers; Novell
Control Panel for Large-Format Printers 4-7 4 HP DesignJet Control Panel To configure a NetWare frame type If you haven't already done so, enable Novell NetWare by following the instructions described in “To enable or disable network protocols” in this chapter. For the 600 Series Printers 1. Access ...
Page 76 - -8 Control Panel for Large-Format Printers; AUTO; Single Route; MIO SETUP
4-8 Control Panel for Large-Format Printers Configuring Novell NetWare Source Routing(Token Ring Card Only) You can select the method for Novell NetWare source routing from the control panel. The possible routing methods are: • AUTO (default): Source routing will be enabled on a packet- by-packet ba...
Page 77 - Control Panel for Large-Format Printers 4-9
Control Panel for Large-Format Printers 4-9 4 HP DesignJet Control Panel For the 700/2000/2500/3000/3500 Series Printers 1. Access the configuration menu (see “To enable or disable network protocols” in this chapter). 2. From the CFG IPX/SPX=NO → menu item, press [Enter] , ↓ , [Enter] to display CFG...
Page 78 - -10 Control Panel for Large-Format Printers
4-10 Control Panel for Large-Format Printers NOTE For DHCP (Dynamic Host Configuration Protocol) operation, BOOTP must be enabled. If an IP address is configured through DHCP and is subsequently changed through the control panel, the DHCP assigned address is released. If a printer is configured thro...
Page 79 - Control Panel for Large-Format Printers 4-11
Control Panel for Large-Format Printers 4-11 4 HP DesignJet Control Panel 5. Press ↑ to configure each TCP/IP parameter. For the first parameter, MIO SETUP and IP BYTE 1=<value> → appear. 6. To maintain the current value, press ↑ . 7. To change the value, proceed as follows: a. Press [Enter] t...
Page 80 - -12 Control Panel for Large-Format Printers
4-12 Control Panel for Large-Format Printers • If you select BOOTP=NO →, the printer is configured to accept TCP/IP parameters from the control panel. Continue with step 4. 4. If you selected BOOTP=NO → , press ↑ to configure each TCP/IP parameter. For example, to configure the IP address: a. Press ...
Page 81 - Control Panel for Large-Format Printers 4-13
Control Panel for Large-Format Printers 4-13 4 HP DesignJet Control Panel Configuring Apple EtherTalk Phase Parameters (Ethernet Cards Only) NOTE EtherTalk is supported by HP DesignJet 650C, Series 700, and 2500CP series printers with PostScript modules installed. You can set Apple EtherTalk paramet...
Page 82 - -14 Control Panel for Large-Format Printers; To set the JOB TIMEOUT
4-14 Control Panel for Large-Format Printers For the 700/2000/2500/3000/3500 Series Printers 1. Access the configuration menu (see “To enable or disable network protocols” in this chapter). 2. From the CFG ETALK=NO → menu item, press [Enter] , ↓ , [Enter] to display CFG ETALK=YES → . 3. Press ↑ to d...
Page 83 - Control Panel for Large-Format Printers 4-15
Control Panel for Large-Format Printers 4-15 4 HP DesignJet Control Panel 6. To access the network configuration menu, press [Enter] to display CFG NETWORK and NO * . 7. Press ↑ to display: CFG NETWORK and YES . 8. Press [Enter] . MIO SETUP and CFG NETWORK=YES → appear. You can now access the networ...
Page 84 - -16 Control Panel for Large-Format Printers
Page 85 - Specifications and Regulatory Statements A-1; Specifications; Specifications and Regulatory Statements; Electrical; Operating
Specifications and Regulatory Statements A-1 A Specifications A Specifications and Regulatory Statements Specifications for HP J4100A, J4105A, and J4106A Print Server Cards Electrical Environmental Electromagnetic Emissions *For EU immunity compliance, see the Declaration of Conformity on page A-4. ...
Page 86 - A-2 Specifications and Regulatory Statements; Regulatory Statements; FCC Statements; General Information; Interference Handbook
A-2 Specifications and Regulatory Statements Regulatory Statements FCC Statements General Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference...
Page 87 - Specifications and Regulatory Statements A-3; European Community
Specifications and Regulatory Statements A-3 A Specifications • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. European Community When used with Ethernet, IEEE 802.3/802.3u...
Page 88 - A-4 Specifications and Regulatory Statements; Declaration of Conformity
A-4 Specifications and Regulatory Statements Declaration of Conformity The following Declaration of Conformity complies with ISO/IEC Guide 22 and EN45014. It identifies the product, the manufacturer’s name and address, and the applicable specifications that are recognized in the European community.
Page 89 - Specifications and Regulatory Statements A-5; Australia
Specifications and Regulatory Statements A-5 A Specifications Australia This equipment complies with Australian EMC requirements. Canada This equipment complies with Canadian EMC Class-A requirements. Japan: VCCI Class A. RRL Statement (Korea). Taiwan Class A.
Page 90 - A-6 Specifications and Regulatory Statements; Chinese Safety Statement
A-6 Specifications and Regulatory Statements Chinese Safety Statement
Page 91 - Supported Links; Off
HP J4100A 10/100Base-TX Print Server B-1 B J4100A 10/100Base-TX B HP J4100A 10/100Base-TX Print Server Supported Links HP J4100A JetDirect 10/100 Base-TX print servers support 10 or 100 Mbps operation in full- or half-duplex modes. In most cases, full-duplex is supported when the connecting network ...
Page 92 - Link Configuration Jumper Settings; Jumper
B-2 HP J4100A 10/100Base-TX Print Server Link Configuration Jumper Settings The HP J4100A JetDirect 10/100Base-TX card provides link configuration jumpers that may be manually set if autonegotiation is not able to connect the card to the network. You can set the link operation for 100 Mbps Full Dupl...
Page 93 - Link Troubleshooting
HP J4100A 10/100Base-TX Print Server B-3 B J4100A 10/100Base-TX Link Troubleshooting If the HP J4100A JetDirect 10/100Base-TX print server does not successfully connect to the network, both LEDs will be off and a “LOSS OF CARRIER ERROR” will be indicated in the MIO section of the HP JetDirect self-t...
