Epson F7070- Manuals

4 | R e p l a c i n g t h e I n k a n d C h i p U n i t 4. Remove the chip unit from the slider. 5. Confirm that the color of the label on the slider matches the color of the label on the new ink pack. Then attach the chip unit supplied with the new ink pack to the slider.

6 | R e p l a c i n g t h e I n k a n d C h i p U n i t 8. Open the slider ink inlet cover. 9. Remove the ink inlet cap from the ink tank.

R e p l a c i n g t h e I n k a n d C h i p U n i t | 7 English 10. Cut or tear off the ink pack spout seal. 11. Insert the spout of the ink pack into the groove and slowly tilt it to pour out the ink. Note: Be sure to completely empty the ink pack into the tank. Do not use an ink pack to refill mul...

8 | R e p l a c i n g t h e I n k a n d C h i p U n i t 12. Put the ink inlet cap back on the ink tank. 13. Close the slider ink inlet cover. EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. General Notice: Other product...

C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e | 9 Fr a n ça is Lorsque le message Carte à puce vide s’affiche sur le panneau de commande, cela indique que vous devrez bientôt remettre de l’encre et remplacer la puce. Procurez-vous dès que possi...

10 | C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e Remarque : • Coupez ou déchirez doucement l’embout du bec verseur de la recharge d’encre. • Si vous coupez l’embout du bec verseur de la recharge d’encre trop rapidement, de l’encre risque de g...

C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e | 11 Fr a n ça is Si le niveau d’encre restante est supérieur à 70 mm (2,8 po) depuis le fond du réservoir d’encre : Nous vous conseillons de continuer à utiliser l’imprimante jusqu’à ce que le nive...

12 | C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e 4. Retirez la puce de la réglette. 5. Vérifiez que la couleur de l’étiquette de la réglette correspond à celle de l’étiquette de la nouvelle recharge d’encre. Puis, installez la puce fournie av...

C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e | 13 Fr a n ça is 6. Tenez la réglette à l’horizontale et insérez-la. Abaissez le levier de verrouillage. Mise en garde : N’appuyez pas trop fort sur la réglette. Le non-respect de cette consigne pe...

14 | C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e 8. Ouvrez le couvercle de l’orifice du réservoir d’encre. 9. Retirez le bouchon de l’orifice du réservoir d’encre.

16 | C o m m e n t r e m p l i r l e s r é s e r v o i r s d ' e n c r e e t r e m p l a c e r l a p u c e 12. Remettez le bouchon du réservoir d’encre en place. 13. Replacez le couvercle de l’orifice du réservoir d’encre. EPSON et SureColor sont des marques déposées et EPSON Exceed Your Vision est ...

C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p | 17 Esp a ñ o l Cuando aparece el mensaje Unidad chip agotada en el panel de control de la impresora, significa que dentro de poco tendrá que rellenar uno de los tanques de tinta y reemplazar su chip. Obteng...

18 | C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p Nota: • Corte o arranque con cuidado el sello del paquete de tinta. • Si corta el sello demasiado rápido, la tinta puede salpicar. • No apriete los paquetes de tinta abiertos. La tinta se podría derramar...

C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p | 19 Esp a ñ o l Si el nivel de tinta restante es inferior a 2,8 pulg. (70 mm): Continúe con el paso 2. 2. Levante la palanca de bloqueo del chip que desea reemplazar. 3. Coloque el dedo en el hueco superior ...

20 | C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p 4. Retire el chip de la barra deslizante. 5. Compruebe que el color de la etiqueta sobre la barra deslizante coincida con el color del paquete de tinta. Luego, coloque el chip incluido con el paquete de ...

22 | C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p 8. Abra la cubierta exterior del tanque de tinta. 9. Quite la tapa de caucho del tanque de tinta.

C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p | 23 Esp a ñ o l 10. Corte o arranque el sello del paquete de tinta. 11. Introduzca el pico del paquete de tinta en el tanque de tinta e incline el paquete lentamente hasta que se vierta toda la tinta. Nota: ...

24 | C ó m o r e l l e n a r l o s t a n q u e s d e t i n t a y r e e m p l a z a r e l c h i p 12. Vuelva a colocar la tapa de caucho en el tanque de tinta. 13. Cierre la cubierta exterior del tanque de tinta. EPSON y SureColor son marcas registradas y EPSON Exceed Your Vision es un logotipo regis...

Como recarregar o tanque de tinta e trocar o chip | 25 Port u g u ê s Quando a mensagem Unidade do chip gasta for apresentada no painel de controle, isso significa que o tanque de tinta precisa ser recarregado e o chip precisa ser substituído em breve. Adquira uma embalagem de tinta, de cor apropria...

26 | Como recarregar o tanque de tinta e trocar o chip Nota: • Corte ou rasgue cuidadosamente o selo do bocal da embalagem de tinta. • Se cortar o bocal da embalagem muito rapidamente, a tinta pode espirrar. • Não aperte embalagens de tinta abertas, pois a tinta pode derramar. • Incline a embalagem ...

Como recarregar o tanque de tinta e trocar o chip | 27 Port u g u ê s Se o nível da tinta restante for igual ou inferior a 70 mm (2,8 pol.): Vá para o passo 2. 2. Abra a tampa do tanque de tinta. 3. Insira um dedo no entalhe situado na parte de cima da barra deslizante e puxe-a para fora. Importante...

28 | Como recarregar o tanque de tinta e trocar o chip 4. Retire o chip da barra deslizante. 5. Confirme se a cor da etiqueta da barra deslizante coincide com a cor da etiqueta do chip. Depois coloque o chip fornecido com a nova embalagem de tinta na barra deslizante.

30 | Como recarregar o tanque de tinta e trocar o chip 8. Abra a tampa da entrada da tinta. 9. Retire a proteção da entrada do tanque de tinta.

Como recarregar o tanque de tinta e trocar o chip | 31 Port u g u ê s 10. Corte ou rasgue o selo do bocal da embalagem de tinta. 11. Insira o bocal da embalagem de tinta na ranhura e incline a embalagem lentamente para despejar a tinta. Nota: Esvazie a embalagem de tinta completamente dentro do tanq...

32 | Como recarregar o tanque de tinta e trocar o chip 12. Recoloque a proteção da entrada do tanque de tinta. 13. Feche a tampa da entrada da tinta. EPSON e SureColor são marcas registradas, e EPSON Exceed Your Vision é uma logomarca registrada da Seiko Epson Corporation. Aviso geral: Outros nomes ...

U n p a c k i n g t h e P r i n t e r | 5 Media System Assembly The items below can be found in the “Ink Supply System Cover 1” box. Media feeding unit Take-up reel Reel brackets Adjustment paper Roll core Bracket and mounting hardware

6 | A s s e m b l i n g t h e S t a n d Assembling the Stand Make sure you have the following items before assembling the stand. 1. Slide the large horizontal strut into both of the legs. 2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs. back of stand

A s s e m b l i n g t h e S t a n d | 7 3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and left legs. 4. Attach the waste ink tank bracket and secure it with a B screw. 5. Attach one B screw to the other side of the bracket, move the slider into...

8 | A s s e m b l i n g t h e S t a n d 6. Temporarily fasten the waste ink tube bracket using one B screw. 7. Remove the four screws, then remove the plastic piece. 8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.

A s s e m b l i n g t h e S t a n d | 9 9. Slide the mounting pieces into the grooves, as shown. 10. Remove the screw, align the bracket, then fasten the screw to the stand. 11. Tighten the screws.

10 | I n s t a l l i n g t h e P r i n t e r 12. Replace the plastic piece and then fasten it using the screws from step 7. Installing the Printer You need six people to install the printer; four people to carry it and two people to position it on the stand. Use the carry bars to lift and move the p...

I n s t a l l i n g t h e P r i n t e r | 11 2. Insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are inserted, rotate them counterclockwise 180° to lock them into place. This keeps the printer from sliding when lifted. Caution: Before...

12 | I n s t a l l i n g t h e P r i n t e r 4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stand’s legs before setting the printer down. 5. Rotate the carry bars clockwise 180° so the locking bolts face the ground. Remove the car...

I n s t a l l i n g t h e P r i n t e r | 13 7. Open the front cover and remove the tape. 8. Remove the media holding plates. 9. Feed the long waste ink tube through the hole in the stand and secure it in place.

14 | I n s t a l l i n g t h e P r i n t e r 10. Feed the short waste ink tube through the bracket as shown. Then feed the end of the long waste ink tube into the top of the short waste ink tube. 11. Remove the cap and inner seal from the waste ink tank. Note: Keep the cap and inner seal for the was...

I n s t a l l i n g t h e M e d i a F e e d i n g U n i t | 15 13. Place the caution label for your language over the English label, if necessary. Installing the Media Feeding Unit You need the following parts to assemble and attach the media feeding unit: 1. Attach the brackets to the back side of ...

16 | I n s t a l l i n g t h e M e d i a F e e d i n g U n i t Caution: The media feeding unit is heavy and requires two people to install. To avoid damaging the media feeding unit, lift it by holding the two bars on the bottom as shown. 2. Lower the media feeding unit onto the brackets. 3. Attach t...

I n s t a l l i n g t h e M e d i a F e e d i n g U n i t | 17 4. Attach the media feeding unit to the stand using four C screws. Note: Leave the screws loose until the service engineer finishes adjusting the media system. 5. Run the communication cable through the cable supports. 6. Lift the port c...

I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 19 Installing the Take-up Reel System You need the following parts to assemble and attach the take-up reel system: 1. Attach the brackets to the front of the printer using two C screws on each side as shown. Caution: Use at least two peop...

20 | I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m 2. Lower the take-up reel onto the brackets. 3. Attach the take-up reel using three C screws as shown. 4. Attach the take-up reel to the stand using four C screws. Note: Leave the screws loose until the service engineer finishes adjust...

I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 21 5. Connect the communication cable that is attached to the take-up reel system by running it through the horizontal struts to the back of the printer. Place the communication cable in the cable supports and plug it in, making sure to t...

22 | S e t t i n g t h e L a n g u a g e 7. Thread the power cord through the cable supports. Connect the power cord to the printer and use the cable supports to restrain the cord. 8. Contact a service engineer to attach the Epson Genuine Ink Supply System, Ink Supply System Cover 1, and adjust the ...

A d j u s t i n g t h e M e d i a S y s t e m | 23 Adjusting the Media System After completing printer assembly and before loading media, mark the loading position on the left end of the media using the procedure below. This ensures that the media will be fed straight and helps reduce printing error...

24 | A d j u s t i n g t h e M e d i a S y s t e m 3. Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide. Align the right side of the adjustment paper with the longest scale marks on both labels. After aligning the adjustment paper, lower the media load...

L o a d i n g M e d i a | 25 5. Raise the media loading lever and remove the adjustment paper. Loading Media 1. Turn on the printer.

26 | L o a d i n g M e d i a 2. Open the front cover and then raise the media loading lever. 3. Loosen the screws on the roll holders and slide the roll holders towards the outside of the printer. 4. Align the left end of the media with the mark you made on the label.

L o a d i n g M e d i a | 29 9. Pull the media into the printer. If the left end of the media is not at the center of the rectangular area as shown in the figure on the right, return to step 4. 10. Lower the media loading lever. 11. Pull the media through the front of the printer and then raise the ...

I n s t a l l i n g t h e S o f t w a r e | 31 14. Close the front cover. 15. After loading the media, you will be prompted to choose setup and media options. Choose options as necessary. Installing the Software Insert the software CD that came with your printer into your computer and follow the on-...

32 | U S B I n s t a l l a t i o n USB Installation 1. Power off your printer, then connect the USB cable to the printer and your computer. 2. Insert the CD into your computer. 3. Follow the on-screen instructions to complete the installation.

N e t w o r k I n s t a l l a t i o n | 33 Network Installation 1. Make sure your printer is powered on. 2. Connect the Ethernet cable to the printer and your networking device. 3. Insert the CD into your computer.

34 | N e t w o r k I n s t a l l a t i o n 4. Follow the on-screen instructions to complete the installation, keeping the following points in mind: • Do not remove the checkmark from EpsonNet Configuration Utility and EPSON drivers and utilities in the software list. • If you see a firewall or netwo...