Epson V11HB23020 - Manual

Quick Setup

IMPORTANT:

Before using this product, make sure you read these instructions

and the safety instructions in the online User’s Guide.

Note:

Your product may differ from the illustrations on this sheet, but the

instructions are the same.

Choose a location

Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use the
lens shift feature to reposition the image (see “Adjust the image”).

See the online User’s Guide for more information on where to place your
projector.

Connect the projector

Connect multiple video devices and use the

Source

buttons on the remote

control or the

Source

button on the projector to switch between them. For

additional connection types, see the online User’s Guide.

HDMI

TM

cable

Power supply

USB cable

Streaming

device

Note:
•

When projecting images at 4K 120Hz, use an HDMI 2.1 rated cable (ultra-high

speed).

•

You can output audio to an external sound system that supports

using the

HDMI

™

2 (eARC/ARC)

port.

•

If you are connecting an optical HDMI cable that has a power supply USB cable,

you must also connect the cable’s USB power connector to the

Opt.HDMI

™

(300mA)

port.

Wired network

Connect the projector to your network using an Ethernet cable. See “Wired
network configuration” for more information.

Ethernet cable

Turn on your equipment

1

Plug in the projector.

2

Press the

power button on the projector or the

On

button on the

remote control. The shutter opens and the

power light flashes blue,

then stays on.

Note:

To shut down the projector, press the

power button on the

projector or the

Standby

button on the remote control, then press the

button again to confirm, if necessary. Wait for cooldown to complete
before unplugging the projector.

3

Use the arrow and Enter buttons on the remote control to select the focus,
image orientation, and language settings.

Note:

To change these settings, see the online User’s Guide.

4

Turn on your video source.

5

If you don’t see an image, press one of the

Source

buttons on the remote

control to select the image source.

Note:

If you still see a blank screen or have other display problems, see the

troubleshooting tips on this sheet.

Using the remote control

Install the batteries as shown (two AA batteries).

Choose which source to

display

Turn projector on

Access projector menus

Adjust zoom, focus,

and lens shift

Turn off projector
display

Navigate projector
menus

Turn projector off

Control connected

sources with HDMI

Link

For more information on using the remote control, see the online User’s Guide.

Adjust the image

1

Press the

Pattern

button on the remote control to display a test pattern.

2

Press the

Lens

button on the remote control and use the and buttons

to focus the image.

3

Press the

Lens

button on the remote control again and use the and

buttons to reduce or enlarge the image.

4

Press the

Lens

button on the remote control again and use the , ,

, and buttons to reposition the image.

Wired network

configuration

Follow these steps to set up your projector for a wired network connection.

1

Press the

Menu

button on the remote control, select the

Network

menu,

then press

Enter

.

2

Choose

Network Settings

and press

Enter

.

3

Select the

Wired LAN

menu and press

Enter

.

4

Choose

IP Settings

and press

Enter

.

5

If your network assigns addresses automatically, make sure the

DHCP

setting is on. If not, make sure DHCP is off and enter the projector’s

IP Address

,

Subnet Mask

, and

Gateway Address

, as needed. Then

press

Esc

.

6

To prevent the IP address from appearing on the network standby screen,
set the

IP Address Display

setting to

Off

.

7

When you are finished, return to the Network Settings menu and select

Set

to apply your settings. Then select

Yes

to save the settings.

Note:

If you are prompted to enter a password for Epson Web Control, you

can create a password or leave it blank. If you do not set a password, you
cannot use Epson Web Control.

8

Press the

Menu

button to exit the menu system.

Using web control

You can use a standard web browser to control the projector through the
network. A virtual remote control on your computer or mobile device screen lets
you perform many of the same functions as you can with the physical remote
control.

1

Open your web browser and enter the IP address of the projector you want
to monitor in the browser’s address bar. The Epson Web Control menu
opens.

If you’re not sure what the IP address of the projector is, turn the projector
on and select

Wired LAN Info

from the Network menu to display the IP

address of the projector. (Do not enter the leading zeroes.)

2

Select

Basic Control

or

Remote

. If you see a login screen, enter

EPSONWEB

as the user name. If a password was created, enter the

password.

3

Use the on-screen buttons to operate the projector, as you would using the
remote control. See the online User’s Guide for details.

Turn off picture

and sound

Select input source

Troubleshooting

•

If you see a blank screen, check the following:

•

Make sure your computer or video device is properly connected.

•

Make sure the

power and Status lights on the projector are blue and

not flashing.

•

Press the

power button on the projector or the remote control to

wake the projector from standby or sleep mode, if necessary.

•

If you see a blank screen when a computer is connected, check the
following:

•

On Windows

®

, hold down the Windows key and press

P

at the same

time, then click

Duplicate

.

•

If you are using a Mac laptop with macOS 13 or newer, select

System

Settings

>

Displays

. Select the projector, then choose the mirror

option for your display from the Use as pop-up menu.

On macOS 12, select

System Preferences

>

Displays

>

Display

Settings

. Select the projector, then choose the mirror option for your

display from the drop-down menu.

On macOS 11 and older, open

System Preferences

and select

Displays

. Click the

Arrangement

tab and select the

Mirror Displays

checkbox.

•

If the projector does not respond to remote control commands, make sure
the batteries in the remote control are installed correctly. Replace the
batteries, if necessary.

EH-QB1000B/EH-QB1000W