Page 2 - Contents
2 | Contents Unpacking the Printer ........................................................................................................................... 3Assembling the Stand ..........................................................................................................................
Page 3 - U n p a c k i n g t h e P r i n t e r; User’s Guide; Unpacking the Printer; Callout
U n p a c k i n g t h e P r i n t e r | 3 Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer and in the User’s Guide . Unpacking the Printer Before beginning assembly, make sure you have sufficient space to set up and ...
Page 4 - The following items should be included with your printer:
4 | U n p a c k i n g t h e P r i n t e r When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct sunlight, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable location that can support 496 lb (225 k...
Page 5 - Media System Assembly
U n p a c k i n g t h e P r i n t e r | 5 Media System Assembly The items below can be found in the “Ink Supply System Cover 1” box. Media feeding unit Take-up reel Reel brackets Adjustment paper Roll core Bracket and mounting hardware
Page 6 - A s s e m b l i n g t h e S t a n d; Assembling the Stand; Slide the large horizontal strut into both of the legs.
6 | A s s e m b l i n g t h e S t a n d Assembling the Stand Make sure you have the following items before assembling the stand. 1. Slide the large horizontal strut into both of the legs. 2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs. back of stand
Page 7 - Attach the smaller horizontal strut by securing two B
A s s e m b l i n g t h e S t a n d | 7 3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and left legs. 4. Attach the waste ink tank bracket and secure it with a B screw. 5. Attach one B screw to the other side of the bracket, move the slider into...
Page 8 - Temporarily fasten the waste ink tube bracket using one B screw.
8 | A s s e m b l i n g t h e S t a n d 6. Temporarily fasten the waste ink tube bracket using one B screw. 7. Remove the four screws, then remove the plastic piece. 8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.
Page 9 - Slide the mounting pieces into the grooves, as shown.
A s s e m b l i n g t h e S t a n d | 9 9. Slide the mounting pieces into the grooves, as shown. 10. Remove the screw, align the bracket, then fasten the screw to the stand. 11. Tighten the screws.
Page 10 - I n s t a l l i n g t h e P r i n t e r; Installing the Printer
10 | I n s t a l l i n g t h e P r i n t e r 12. Replace the plastic piece and then fasten it using the screws from step 7. Installing the Printer You need six people to install the printer; four people to carry it and two people to position it on the stand. Use the carry bars to lift and move the p...
Page 11 - Lift the printer as shown.
I n s t a l l i n g t h e P r i n t e r | 11 2. Insert the carry bars into both sides of the printer with the locking bolts toward the ground. Once the carry bars are inserted, rotate them counterclockwise 180° to lock them into place. This keeps the printer from sliding when lifted. Caution: Before...
Page 12 - Attach the printer to the stand using three A
12 | I n s t a l l i n g t h e P r i n t e r 4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stand’s legs before setting the printer down. 5. Rotate the carry bars clockwise 180° so the locking bolts face the ground. Remove the car...
Page 13 - Open the front cover and remove the tape.
I n s t a l l i n g t h e P r i n t e r | 13 7. Open the front cover and remove the tape. 8. Remove the media holding plates. 9. Feed the long waste ink tube through the hole in the stand and secure it in place.
Page 14 - Remove the cap and inner seal from the waste ink tank.
14 | I n s t a l l i n g t h e P r i n t e r 10. Feed the short waste ink tube through the bracket as shown. Then feed the end of the long waste ink tube into the top of the short waste ink tube. 11. Remove the cap and inner seal from the waste ink tank. Note: Keep the cap and inner seal for the was...
Page 15 - I n s t a l l i n g t h e M e d i a F e e d i n g U n i t; Installing the Media Feeding Unit
I n s t a l l i n g t h e M e d i a F e e d i n g U n i t | 15 13. Place the caution label for your language over the English label, if necessary. Installing the Media Feeding Unit You need the following parts to assemble and attach the media feeding unit: 1. Attach the brackets to the back side of ...
Page 16 - Lower the media feeding unit onto the brackets.
16 | I n s t a l l i n g t h e M e d i a F e e d i n g U n i t Caution: The media feeding unit is heavy and requires two people to install. To avoid damaging the media feeding unit, lift it by holding the two bars on the bottom as shown. 2. Lower the media feeding unit onto the brackets. 3. Attach t...
Page 17 - Attach the media feeding unit to the stand using four C screws.
I n s t a l l i n g t h e M e d i a F e e d i n g U n i t | 17 4. Attach the media feeding unit to the stand using four C screws. Note: Leave the screws loose until the service engineer finishes adjusting the media system. 5. Run the communication cable through the cable supports. 6. Lift the port c...
Page 19 - I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m; Installing the Take-up Reel System
I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 19 Installing the Take-up Reel System You need the following parts to assemble and attach the take-up reel system: 1. Attach the brackets to the front of the printer using two C screws on each side as shown. Caution: Use at least two peop...
Page 20 - Lower the take-up reel onto the brackets.
20 | I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m 2. Lower the take-up reel onto the brackets. 3. Attach the take-up reel using three C screws as shown. 4. Attach the take-up reel to the stand using four C screws. Note: Leave the screws loose until the service engineer finishes adjust...
Page 21 - Attach the cable support to the bottom of the printer.
I n s t a l l i n g t h e T a k e - u p R e e l S y s t e m | 21 5. Connect the communication cable that is attached to the take-up reel system by running it through the horizontal struts to the back of the printer. Place the communication cable in the cable supports and plug it in, making sure to t...
Page 22 - S e t t i n g t h e L a n g u a g e; Setting the Language; Menu
22 | S e t t i n g t h e L a n g u a g e 7. Thread the power cord through the cable supports. Connect the power cord to the printer and use the cable supports to restrain the cord. 8. Contact a service engineer to attach the Epson Genuine Ink Supply System, Ink Supply System Cover 1, and adjust the ...
Page 23 - A d j u s t i n g t h e M e d i a S y s t e m; Adjusting the Media System; Open the front cover and raise the media loading lever.
A d j u s t i n g t h e M e d i a S y s t e m | 23 Adjusting the Media System After completing printer assembly and before loading media, mark the loading position on the left end of the media using the procedure below. This ensures that the media will be fed straight and helps reduce printing error...
Page 24 - A d j u s t i n g t h e M e d i a S y s t e m
24 | A d j u s t i n g t h e M e d i a S y s t e m 3. Align the bottom of the adjustment paper with the bottom of the lower label on the ejection guide. Align the right side of the adjustment paper with the longest scale marks on both labels. After aligning the adjustment paper, lower the media load...
Page 25 - L o a d i n g M e d i a; Raise the media loading lever and remove the adjustment paper.; Loading Media
L o a d i n g M e d i a | 25 5. Raise the media loading lever and remove the adjustment paper. Loading Media 1. Turn on the printer.
Page 26 - Open the front cover and then raise the media loading lever.
26 | L o a d i n g M e d i a 2. Open the front cover and then raise the media loading lever. 3. Loosen the screws on the roll holders and slide the roll holders towards the outside of the printer. 4. Align the left end of the media with the mark you made on the label.
Page 29 - Lower the media loading lever.
L o a d i n g M e d i a | 29 9. Pull the media into the printer. If the left end of the media is not at the center of the rectangular area as shown in the figure on the right, return to step 4. 10. Lower the media loading lever. 11. Pull the media through the front of the printer and then raise the ...
Page 31 - I n s t a l l i n g t h e S o f t w a r e; Close the front cover.; Installing the Software; You can use USB or Ethernet network connections.
I n s t a l l i n g t h e S o f t w a r e | 31 14. Close the front cover. 15. After loading the media, you will be prompted to choose setup and media options. Choose options as necessary. Installing the Software Insert the software CD that came with your printer into your computer and follow the on-...
Page 32 - U S B I n s t a l l a t i o n; USB Installation; Insert the CD into your computer.
32 | U S B I n s t a l l a t i o n USB Installation 1. Power off your printer, then connect the USB cable to the printer and your computer. 2. Insert the CD into your computer. 3. Follow the on-screen instructions to complete the installation.
Page 33 - N e t w o r k I n s t a l l a t i o n; Network Installation; Make sure your printer is powered on.
N e t w o r k I n s t a l l a t i o n | 33 Network Installation 1. Make sure your printer is powered on. 2. Connect the Ethernet cable to the printer and your networking device. 3. Insert the CD into your computer.
Page 34 - Do not remove the checkmark from; EpsonNet Configuration Utility; and; EPSON drivers and; in the software list.
34 | N e t w o r k I n s t a l l a t i o n 4. Follow the on-screen instructions to complete the installation, keeping the following points in mind: • Do not remove the checkmark from EpsonNet Configuration Utility and EPSON drivers and utilities in the software list. • If you see a firewall or netwo...
