Teledyne 760 PLUS - Manual

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 5 of 16 1.2. Specifications Piezo Vacuum Transducer (760s): Accuracy ......................................................................................................± 0.25% FS* (760 Torr) Operating pressure ........................................

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 6 of 16 2. Installation This section contains the necessary instructions to assist in placing the HPM-760 Plus digital vacuum gauge into operation as quickly and easily as possible. Please read the following thoroughly before attempting to install or...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 7 of 16 2.3. Power Supply/Display Installation Cut a panel opening to the following dimensions; 3.62” (92mm) wide, 1.77” (45mm) tall. Insert the power supply/display through the panel cutout and secure in place using mounting hardware supplied. 2.3.1...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 8 of 16 3. Operating Information This section contains information on operating the PIEZO Resistive Transducer in any of its various configurations. Refer to the appropriate section for information on the mode in use. 3.1. General The piezoresistive ...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 9 of 16 3.2. Piezo Transducer Input Power The 760s piezo transducer operates with a DC input from 15 to 30 volts. Use the 4-pin female connector supplied and makes necessary connections as outlined. See illustration in Section 2 of this manual. 3.3. ...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 10 of 16 3.5.2. Rear Panel Refer to page 19, 7.1.2 for rear view and specific pin outs and connector arrangements. AC Input Connector J1 Universal input power 110vac to 220 VAC. No hardware settings required. J3 Input/Output Connector Sensor Input (p...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 11 of 16 Auxiliary Relay Contacts The THPS-760 Power Supply has SP1 and SP2 relays for various external switching/monitoring applications. Each relay has a single set of Form “C” contacts. (Choice of normally open or normally closed contacts). The re...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 12 of 16 4. Calibration 4.1. Hastings 760 Plus Piezo Transducer Zero and Span Adjustment 1. Install the transducer and power supply/display then apply operating power. Wait a mini mum of 15 minutes before proceeding. 2. Evacuate system to a pressure ...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 14 of 16 6. WARRANTY 6.1. Warranty Repair Policy Hastings Instruments warrants this product for a period of one year from the date of shipment to be free from defects in material and workmanship. This warranty does not apply to defects or failures re...

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 15 of 16 7. Diagrams and Drawings 7.1. Front Panel The THPS-760 has a 4 1/2-digit display that displays continuous readout. 7.2. Rear Panel Decal is to be black ink printed on silver compucal, with adhesive on the back

Manual: 147-082010_HPM-760-Plus-Vacuum-Gauge Page 16 of 16 7.3. Mounting Cut out panel as shown in the diagram below. 7.4. Panel Mounting 1) Slide power supply into panel from the top. 2) Attach brackets to the side of the power supply. 3) Tighten screws against panel.