Teka EM/30 2P (EXP) - User Manual

GB 7 Important INSTALLATION AND SETUP SHOULDBE CARRIED OUT BY AN AUTHORISEDTECHNICIAN IN LINE WITH CURRENTINSTALLATION STANDARDS. Positioning the hobs A gap with the dimensions shown in figure1 will be cut into the worktop or stove. The system for fixing the hob is intendedfor use with kitchen units...

GB 8 TEKA assumes no responsibility for any malfunction or damage causedby faulty installation. PLEASE REMEMBER THAT THE GUA-RANTEE DOES NOT COVER THEGLASS IF IT SUFFERS A VIOLENTBLOW OR IF IT IS USED IMPROPERLY. Positioning the oven See the corresponding manual. Fixing the hob When the gap has been...

GB 9 located lower down, and on the guaranteecertificate or, where appropriate, the tech-nical datasheet supplied, which should bekept together with this manual. The connection is made via an omnipolarswitch or plug where accessible, which issuitable for the intensity to be toleratedand which has a ...

GB 10 Dimensions and power Models Hob dimensions Height (mm) 90 90 90 90 Length (mm) 510 510 510 510 Width (mm) 300 300 300 300 Dimensions of the placement in the unit Length (mm) 490 490 490 490 Width (mm) 280 280 280 280 Depth (mm) 40 40 40 40 Power per burner and hotplate Gas burner rapid 3 kW. 1...

11 GB Te c h n i c a l i n f o r m a t i o n COMMON FEATURES FOR ALL MODELSWITH ELECTRIC HOTPLATES AND AUTO-MATIC IGNITION The supply voltage and frequency will beas shown on the rating plate. If an electric hotplate gets cracked, thehob should be disconnected from the elec-tricity current. COMMON F...

GB 12 Special requirements before starting for the first time Before connecting the hob to the electricmains, check that the voltage and fre-quency of the mains matches what isshown on the hob’s rating plate, which islocated lower down, and on the guaranteeor, where appropriate, the technical datas-...

GB 13 Only pans with a minimum diameter of 140mm should be used on each burner. If youwish to use a pan with a diameter of 120mm or smaller, it should be placed on theauxiliary burner or on the grid accessory. Please note: When the burners are in opera- tion or have recently been in operation,the ho...

GB 14 signal to the tap. Should the burner go out,the absence of a flame is detected by thethermocouple, which makes the safety tapcut off the flow of gas. Suggestions for effective use of the burners * Rapid burners should not be used with pans that have a small diameter, becau-se part of the flame...

GB 16 When first connecting, or if the hotplatehas not been used for some time, themoisture absorbed by the insulation needsto be eliminated. To carry out this drying process, turn the hotplate on - with no panon it - for five minutes at switch position 2.The smell and smoke that are emitted,while u...

GB 17 * The electric hotplates should be cleaned using soapy water and a non-abrasive scourer. If, after cooking, you notice that the electric hotplate’s stainless steel rimor the cooker’s surround are yellowingslightly, you can counter this by usinglemon, vinegar, dilute amonia or anyproduct contai...

GB 18 hotplates heat up, according to the timewhich has been set. The timer shouldnever be set to zero if the hotplates are towork. Advice on using the electric hotplates effectively In order to achieve the best results fromcooking, the following guidelines shouldbe followed: * Use pans with a flat ...

GB 19 should be cleaned each time it is used,when it is either lukewarm or cool. Thismakes cleaning easier and avoids dirtaccumulating through repeated use. Never use aggressive cleaning products orproducts that can scratch the surfaces (thetable below shows various common pro-ducts that may be used...

GB 21 If something doesn’t work Fault Possible cause Possible solution Neither the hotplates nor the pilot lights are working The cable is not connected to the mains Connect the cable to the mains There is no spark when theautomatic ignition control is pressed There is no current at the plug Check/r...