Teka EH 60 4G AI AL TR CI NAT ANTHR. OS - User Manual

Page 2 - DESCRIPTION OF THE HOT PLATES

2 NG U - LPG 1 Ultra rapid gas burner of 15.0 MJ 11.9 MJ 2 Rapid gas burner of 12.0 MJ 10.8 MJ 3 Semirapid gas burner of 7.0 MJ 6.3 MJ 4 Auxiliary gas burner of 4.0 MJ 3.6 MJ 6 Enamelled steel pan support 2F right 7 Enamelled steel pan support 2F left 8 Burner n° 1 control knob 9 Burner n° 2 control...

Page 3 - USE

3 1) BURNERS A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - manual ignition Push and turn the knob corresponding to t...

Page 5 - CLEANING

5 CLEANING IMPORTANT: always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) HOT PLATE Periodically wash the hot plate, the enamelled steel pan support, the enamelled burner caps “C” and the burner heads “T” (see fig. 6) with lukewarm soapy ...

Page 6 - ) INSTALLING THE HOT PLATE; INSTALLATION

6 TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL T h i s a p p l i a n c e s h a l l b e i n s t a l l e d o n l y b y authorised persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, AS ...

Page 7 - ) FIXING THE HOT PLATE

7 4) FIXING THE HOT PLATE The hot plate has a special seal which prevents liquid from infiltrating into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal: - detach the seals from their backing, checking that the transparent protection still adheres to...

Page 9 - ) ELECTRICAL CONNECTION

9 INSTALLATION 6) ELECTRICAL CONNECTION The appliance is supplied with a 1800 mm long flexible supply lead. The point of attachment for this lead is located at the rear and on the underside of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the unders...

Page 10 - ADJUSTMENTS

10 Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. a) Data Label The Data Label is located on the underside of the ho...

Page 11 - CONVERSION PROCEDURE; CONVERSIONS

11 8) U - LPG TO NATURAL GAS CONVERSION PROCEDURE Appliance models: Gas stainless steel hotplate models: EH/60 4G AI AL TR CI 4 Burners 1. Remove each burner cap and burner skirt. 2 . R e m o v e t h e U - L P G m a i n i n j e c t o r w i t h a 7 m m / V F t u b e s pa n n e r a n d r e p l a c e w...

Page 13 - BURNER ARRANGEMENT ON THE HOT PLATE; EH/60 4G AI AL TR CI model

CONVERSIONS FIG. 14 BURNER ARRANGEMENT ON THE HOT PLATE U - LPG 2.75 0,94 11.9 85 NATURAL 1.00 1,76 15.0 Fully Closed * U - LPG 2.75 0,91 10.8 41 NATURAL 1.00 1,55 12.0 1/2 * U - LPG 2.75 0,70 6.3 32 NATURAL 1.00 1,20 7.0 3/8 * BURNERS N° DESCRIPTION GAS NORMAL PRESSURE INJECTOR DIAMETER NOMINAL HEA...

Page 14 - SERVICING; 0) COMPONENTS REPLACEMENT

14 SERVICING WARNING: s e r v i c i n g s h o u l d b e c a r r i e d o u t o n l y b y authorised personnel. 10) COMPONENTS REPLACEMENT NOTE: B E F O R E A N Y M A I N T E N A N C E R E Q U I R I N G R E P L A C E M E N T O F A C O M P O N E N T I S U N D E RTA K E N E N S U R E T H AT T H E ELECTR...

Page 15 - CABLE TYPES AND SECTIONS

15 SERVICING TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY CABLE TYPES AND SECTIONS ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 21) and comply with the recommendations given in paragraph 6. FIG. 2...

Teka EH 60 4G AI AL TR CI NAT ANTHR. OS - User Manual

Table of Contents:

Summary

Other Teka Hobs Models