Stanley CS06 - Manual

CS05/CS06 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI Z133.1-2000) Working in Proximity to Electrical Hazards: An inspection shall be made by a qualified arborist to dete...

8 ► CS05/CS06 User Manual Table 2 – Minimum approach distances to energized conductors for persons other than qualified line-clearance arborists and qualified line-clearance ar- borist trainees. Nominal Voltage kV phase-to-phase 1 Distance ft-in m 0.0 to 1.0 10–00 3.05 1.1 to 15.0 10–00 3.05 15.1 to...

CS05/CS06 User Manual ◄ 9 28323 CE Decal (CE Models Only) 28409 Composite Decal (CE Models Only) D 30 LPM @ 138 B AREHTMA CATEGORY 11207 Circuit Type D Decal (CE Models Only) Failure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tools on or near electric lines ma...

10 ► CS05/CS06 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy - draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certi...

CS05/CS06 User Manual ◄ 11 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fi...

12 ► CS05/CS06 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient...

CS05/CS06 User Manual ◄ 13 OPERATING PROCEDURES The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less val - id for particu lar areas. For advice on specific woodcut - ting problems or tech...

14 ► CS05/CS06 User Manual FELLING OR BACK CUT 4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking c...

CS05/CS06 User Manual ◄ 15 Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on Top LOGS WITH PRESSURE ON TOP (FIGURE 3) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply. A cut of about 1/3 of the log diameter is enough. 3. Finish...

CS05/CS06 User Manual ◄ 17 PRUNING AND DEBRANCHING 1. Observe all safety precautions. 2. Use both hands. Keep a firm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. 4. Do not cut overhead. Keep the saw below chest lev - el. The chain is...

18 ► CS05/CS06 User Manual • Make sure all couplers are wiped clean before con - nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy - ...

CS05/CS06 User Manual ◄ 19 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw, always make sure the hydraulic power source is supplying the correct hydraulic flow and pressure to the saw as listed...

CS05/CS06 User Manual ◄ 21 CS05/CS06 PARTS ILLUSTRATION

24 ► CS05/06 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif - ferent depth operation. With percus...