Stanley BR87 Manual - Free PDF Download

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; IMPORTANT; TABLE OF CONTENTS

BR87 User Manual ◄ 3 DECLARATION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS ....................................................................................................................

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► BR87 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

BR87 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befor...

Page 8 - HOSE SAFETY TAGS; HOSE TYPES

8 ► BR87 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 9 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

BR87 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 10 - HTMA / EHTMA REQUIREMENTS

10 ► BR87 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat...

Page 11 - COLD WEATHER OPERATION; CHECK POWER SOURCE; OPERATION PROCEDURES; OPERATION

BR87 User Manual ◄ 11 NOTE: Partially depressing the trigger allows the tool to run at slow speed. Slow-speed operation permits easier starting of the tool bit into the work surface. 5. To start, break an opening (hole) in the center of the surface. After making a hole, break portions of the materia...

Page 12 - TOOL PROTECTION & CARE

12 ► BR87 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic s...

Page 13 - TROUBLESHOOTING

BR87 User Manual ◄ 13 PROBLEM CAUSE REMEDY Tool does not run. Power unit not functioning. Check power unit for proper flow and pressure (7–9 gpm/26–34 lpm, 1500-2000 psi/105–140 bar. Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. Be sure hoses are co...

Page 14 - ACCUMULATOR TESTING; ACCUMULATOR CHARGING; GENERAL SERVICE NOTES; CHARGING THE ACCUMULATOR

14 ► BR87 User Manual ACCUMULATOR TESTING PROCEDURE To check or charge the accumulator the following equip- ment is required:31254 Charge Kit: which includes the following. • Accumulator Tester (Part Number 02835) • Charging Assembly (P/N 15304) (P/N 15304 includes a liquid filled gauge with snub va...

Page 16 - BR87 SOUND AND VIBRATION DECLARATION; SPECIFICATIONS

16 ► BR87 User Manual Pressure Range.............................................................................................................. 1500–2000 psi/105–140 bar Flow Range .......................................................................................................................

Page 17 - ACCESSORIES; TEST EQUIPMENT; SERVICE TOOLS

BR87 User Manual ◄ 17 ACCESSORIES 1-1/8 IN. HEX × 6 IN. SHANK Moil Point, 14 in. Long UC ................................................................................................................................. 02333 Chisel Point, 14 in. Long UC .................................................

Page 18 - BR87 PARTS ILLUSTRATION

Page 20 - BR87 PARTS LIST

20 ► BR87 User Manual Item No. Part No. Qty Description 1 06185 1 HANDLE ASSY (INCL ITEM 35) 11435 1 BREAKER HANDLE (TRIGGER LOCK MODELS ONLY) 2 04050 1 VALVE CAP ASSY 3 04051 1 CHARGING VALVE 4 04052 1 O-RING 5 04053 11434 1 TRIGGER TRIGGER (TRIGGER LOCK MODELS ONLY) 6 00844 1 SPIROL PIN 7 04054 3 ...

Page 21 - UNDERWATER TOOLS DEPTH GUIDELINE; Operation Overview; Diver; Recommended Hose Diameters

BR87 User Manual ◄ 21 For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive...