Stanley BR67 - Manual - manualsarea.com

Page 2 - DECLARATION OF CONFORMITY

2 ► BR67 User Manual DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY ÜBEREINSTIMMUNGS - ERKLARUNG DECLARATION DE CONFORMITE CEE DECLARACION DE CONFORMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools ______________________________________________________________________ I, the undersigned: Ich, d...

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS; IMPORTANT

BR67 User Manual ◄ 3 DECLARATION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS ....................................................................................................................

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► BR67 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

BR67 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety. Re- view them carefully before operating the tool and befo...

Page 8 - HOSE SAFETY TAGS; HOSE TYPES

8 ► BR67 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 9 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

BR67 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 10 - HTMA / EHTMA REQUIREMENTS

10 ► BR67 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat...

Page 11 - COLD WEATHER OPERATION; CHECK POWER SOURCE; OPERATION PROCEDURES; OPERATION

BR67 User Manual ◄ 11 NOTE: Partially depressing the trigger allows the tool to run at slow speed. Slow-speed operation permits easier starting of the tool bit into the work surface. 5. To start, break an opening (hole) in the center of the surface. After making a hole, break portions of the materia...

Page 12 - TOOL PROTECTION & CARE

12 ► BR67 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic ...

Page 13 - TROUBLESHOOTING

BR67 User Manual ◄ 13 PROBLEM CAUSE REMEDY Tool does not run. Power unit not functioning. Check power unit for power flow and pres - sure (7–9 gpm/26–-34 lpm, 1500–2000 psi/ 105–140 bar. Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. Be sure hoses ar...

Page 14 - ACCUMULATOR TESTING; ACCUMULATOR CHARGING; UNDERWATER MODEL; CHARGING THE ACCUMULATOR

14 ► BR67 User Manual ACCUMULATOR TESTING PROCEDURE To check or charge the accumulator the following equip- ment is required.• 31254 Charge Kit, which includes the following: – Accumulator Tester (Part Number 02835). – Charging Assembly (P/N 15304) (15304 in- cludes a liquid filled gauge with snub v...

Page 16 - BR67 SOUND AND VIBRATION DECLARATION; SPECIFICATIONS

16 ► BR67 User Manual Pressure Range.............................................................................................................. 1500–2000 psi/104–140 bar Flow Range .......................................................................................................................

Page 17 - TEST EQUIPMENT; ACCESSORIES

BR67 User Manual ◄ 17 ACCESSORIES 1-1/8 IN. HEX × 6 IN. SHANK Moil Point – 14 in. Long UC ................................................................................................................................................... 02333 Chisel Point – 14 in. Long UC .............................

Page 18 - BR67 ANTI-VIBRATION HANDLE PARTS ILLUSTRATION

18 ► BR67 User Manual BR67 ANTI-VIBRATION HANDLE PARTS ILLUSTRATION BR67 ANTI-VIB PARTS ILLUSTRATION

Page 19 - BR67 ANTI-VIBRATION HANDLE PARTS LIST

BR67 User Manual ◄ 19 ITEM NO. WITHOUT TRIGGER LOCK WITH TRIGGER LOCK QTY DESCRIPTION 1 24067 24067 1 RETAINING RING 2 04055 04055 1 WASHER 3 04056 04056 1 ROD WIPER 4 04057 04057 1 BUSHING 5 01362 01362 1 O-RING 6 00293 00293 1 O-RING 7 20515 20515 1 VALVE SPOOL 8 04058 04058 1 SPRING 9 07628 07628...

Page 20 - BR67 ANTI-VIB PARTS LIST

20 ► BR67 User Manual ITEM NO. WITHOUT TRIGGER LOCK WITH TRIGGER LOCK QTY DESCRIPTION 66 04075 04075 1 SIDE ROD NUT 67 01837 01837 1 LATCH 68 04984 04984 1 STOP NUT 69 01744 01744 1 SPRING 70 08411 08411 1 DETENT 71 — 28322 1 CE STICKER (CE ONLY) 72 28409 28409 1 COMPOSITE STICKER (CE ONLY) 73 66654...

Page 21 - BR67 STANDARD HANDLE PARTS ILLUSTRATION

BR67 User Manual ◄ 21 BR67 STANDARD HANDLE PARTS ILLUSTRATION BR67 STD PARTS ILLUSTRATION

Page 22 - BR67 STANDARD PARTS LIST

22 ► BR67 User Manual ITEM NO. WITHOUT TRIGGER LOCK WITH TRIGGER LOCK QTY DESCRIPTION 1 — — 1 RETAINING RING 2 04055 04055 1 WASHER 3 04056 04056 1 ROD WIPER 4 04057 04057 1 BUSHING 5 01362 01362 1 O-RING 6 00293 00293 1 O-RING 7 04077 04077 1 VALVE SPOOL 8 04058 04058 1 SPRING 9 — — 4 CAPSCREW 10 —...

Page 24 - UNDERWATER TOOLS DEPTH GUIDELINE; Operation Overview; Diver; Recommended Hose Diameters

24 ► BR67 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive...

Page 25 - NOTES