Smeg KR37X - Manual - manualsarea.com

Page 3 - INNEHÅLL

3 3 ÍNDICE CONSELHOS E SUGESTÕES ............................................................................................................................................58 CARACTERÍSTICAS ...............................................................................................................

Page 4 - RECOMMENDATIONS AND SUGGESTIONS; INSTALLATION

EN 13 13 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accord-ingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resultin...

Page 5 - CHARACTERISTICS; Dimensions

EN 14 14 CHARACTERISTICS Dimensions Min. 550mm Min. 550mm 540 Components Ref. Q.ty Product components 1 1 Hood equipped with: Controls, Lights, Filters 3 1 Hood support equipped with the Exhaust Group 7 1 tube in PVC 8 1 Directioned grid 8c 1 Air outlet reduction ø 120mm 9 1 Reduction flange ø 150-1...

Page 6 - Wall drilling and bracket fixing

EN 15 15 INSTALLATION Wall drilling and bracket fixing When installing the hood in recycling version it has to be taken into consideration that space re-maining between the hood and the upper limit (ceiling or self) is at least 8-10 cm. On the wall, draw: • a Vertical line up to the ceiling or upper...

Page 7 - AIR OUTLET ON THE BACK SIDE OF THE HOOD

EN 16 16 Hood support mounting • Lean the hood support 3 against the wall making sure that holes in the hood support correspond to those in the wall. • Block the hood support to the wall using 4 12a (5 x 70) screws supplied with the hood. • Before fastening the screws definitively make sure that the...

Page 8 - RECIRCULATION VERSION AIR OUTLET; Hood body mounting

EN 17 17 RECIRCULATION VERSION AIR OUTLET • Insert pvc pipe 7 provided onto the Hood Canopy Outlet. . 7 ø 150 Hood body mounting Ducting version • In case the air outlet connection on the upper part of the hood has been chosen it will be necessary to remove the pre-cut piece. • Lean the hood body on...

Page 9 - ELECTRICAL CONNECTION; back of the group and pulling down at the same time.

EN 18 18 ELECTRICAL CONNECTION • Connect the hood to the mains through a twopole switch having a contact gap of at least 3 mm. • Open the lighting unit by pulling on the notch. • Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. • Being...

Page 10 - USE; Control panel

EN 19 19 USE L L1 T1 T2 T3 T4 L2 L3 L4 Control panel Button Function Led L Press briefly to turn the lighting system on and off. Press and hold for approx. 2 seconds to turn the lighting system on and off at reduced intensity. - T1 Turn the suction motor on and off at speed one. If the filter satura...

Page 11 - MAINTENANCE; Metal grease filters; back of the unit and at the same time pulling downward.

EN 20 20 MAINTENANCE Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. Resetting the alarm signal • Press any of t...

Page 12 - Activated Charcoal Filter (Recirculation Version); start to flash, or at least once every 4 months.; CHANGING THE ACTIVATED CHARCOAL FILTER; Lighting; LIGHT REPLACEMENT; two pins are properly inserted in the lamp holder socket holes.

EN 21 21 Activated Charcoal Filter (Recirculation Version) • This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal • In Recirculation Version Hoods, the Filter Saturation Alarm must be activate...