Smeg CMZOOM - Manuals

EN 8 8 INSTALLATION This hood is designed to be mounted on the ceiling/on a shelf, above a free-standing Hob (min. 650 mm), in: • Ducting version : Evacuation to the outside. • Recirculation version : Internal recirculation. Warning: The F-Light hood is a system comprising hood + lamp, so that two s...

EN 9 9 Ceiling/Shelf drilling and Plate Fixing CEILING/SHELF DRILLING • Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling/Shelf. • Rest the plate against the ceiling/shelf, taking care to keep the limit pawl that has just been fitted in a position facing the installer an...

EN 1 10 FIXING THE PLATE • Lift up the fixing plate, taking care to ensure that the limit pawl is positioned frontally. • Fit the slots onto the two screws previously inserted in the ceiling, and turn until they are at the centre of the adjustment slot. • Tighten the two screws completely and screw ...

EN 1 11 CONNECTING HOOD-PLATE CABLES N.B. Before continuing with installation it is necessary to move the hood to a height of at least 650 mm from the cooker hob, using a support or the assistance of an-other person. This is essential, as the hood cables must necessarily be connected to the plate fi...

EN 1 12 • Attention to the direction of the plate fixed to the ceiling (the limit pawl on the plate fastened to the ceiling has a corresponding hole on the plate cover and on the hood canopy). • Insert the cables into the safety knobs ( c ) with the thread at the top. • Insert the cables into the ca...

EN 1 13 • Pass the cables through the slots in the threaded pawls ( a ) and screw the cable locking screws ( b ) to the pawls them- selves. • When the operation has been completed the result must be as shown in the figure for all 4 ca-bles. • At this point we have all 4 cables con- nected to the pla...

EN 1 14 • At this point it is possible to connect up the hood, and the lamp if there is one, to the power supply using the respective power cables. • Close the plate cover using the 3 screws removed previously and the wrench provided • At this point the Hood is sus- pended.

EN 1 15 Connections AIR OUTLET - DUCTING VERSION To install the hood in the ducting version, please refer to the instructions provided in the ducting kit specific to the hood. AIR OUTLET – RECIRCULATION VERSION • Open the lighting unit by pulling on the notch provided. • Remove the grease filter. • ...

EN 1 16 LEVELLING THE HOOD • The hood mobile unit must be levelled to allow the movement to operate properly. • The hood is levelled by adjusting the safety pawls. • Rest a spirit level on the hood. • When the safety knobs are pressed upwards, movement of the hood is “unlocked”. By in-serting or ext...

EN 1 17 FIXING THE POWER SUPPLY CABLE • Wind the power cable around its axis so that it forms a spiral from the mobile body to the plate in the ceiling. • It is important to do this to prevent the wire come out from the hood body during the closing of the hood • Take the cable clamp 3 provided. • In...

EN 1 18 FITTING THE GLASS – CHIC-VANILLA MODELS • Take the lamps and insert them in the lamp holders. • They do not have to be screwed in, but simply inserted all the way. • Fix the glass 5 to the plate using the screws 12d and washers 22 in the top part. • Fix the glass elements together at the bot...

EN 1 19 USE Control panel L T1 Button Function Display L Turns the lights On/Off. - T1 Hood Down Press for 2 seconds to raise the Hood. Press briefly to turn the Motor On/Off. On/Off Hood Up Press once: The Hood lowers. Press a second time: The Hood Stops. When the movement has been completed the mo...

EN 2 20 REMOTE CONTROL The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included). • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. Control pan...

EN 2 21 MAINTENANCE Grease filter The filter must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. CLEANING METAL SELF- SUPPORTING GREASE FILTER • Open the lighting unit by pulling on the nocth. • Remove the filter one by one...

EN 2 22 Lighting LIGHT REPLACEMENT 20 W halogen light. • Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. • Remove the halogen lamp from the lamp holder by pulling gently. • Replace the lamp with a new one of the same type, making sure that you ins...

EN 2 23 Additional information for the installation technician • Open the lighting unit by pulling on the notch provided. • Apply the label, indicated the type of lighting, on the Hood as indicated in the figure (Rif. A ). Procedure to be used in case of malfunction on the movement • Check that the ...