Page 2 - INDEX; EN
2 2 INDEX RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS .............................................................................................................................
Page 3 - RECOMMENDATIONS AND SUGGESTIONS; INSTALLATION; USE; MAINTENANCE
EN 3 3 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting f...
Page 4 - CHARACTERISTICS
EN 4 4 CHARACTERISTICS Components (Chic-Vanilla models) Ref. Q.ty Product Components 1 1 Hood Canopy complete with: Controls, Light, Filters, Motor. 2 1 Hood support Plate (with lamp holder). 3 1 Power supply cable lock 4 1 Cable raceway 5 3 Glass 6 3 Glass fixing plates 14 1 Pawl Ref. Q.ty Installa...
Page 7 - Dimensions
Page 8 - Sequence of operations - Installation; • Disposal of Packaging; Fitting the Limiter pawl; the wrench provided.; Warning; : the clamps used to fix the wires
EN 8 8 INSTALLATION This hood is designed to be mounted on the ceiling/on a shelf, above a free-standing Hob (min. 650 mm), in: • Ducting version : Evacuation to the outside. • Recirculation version : Internal recirculation. Warning: The F-Light hood is a system comprising hood + lamp, so that two s...
Page 9 - Ceiling/Shelf drilling and Plate Fixing; CEILING/SHELF DRILLING; Plugs
EN 9 9 Ceiling/Shelf drilling and Plate Fixing CEILING/SHELF DRILLING • Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling/Shelf. • Rest the plate against the ceiling/shelf, taking care to keep the limit pawl that has just been fitted in a position facing the installer an...
Page 10 - FIXING THE PLATE
EN 1 10 FIXING THE PLATE • Lift up the fixing plate, taking care to ensure that the limit pawl is positioned frontally. • Fit the slots onto the two screws previously inserted in the ceiling, and turn until they are at the centre of the adjustment slot. • Tighten the two screws completely and screw ...
Page 11 - CONNECTING HOOD-PLATE CABLES; This is essential, as the hood cables must; necessarily; be connected to the plate; • Cable clamp screws (
EN 1 11 CONNECTING HOOD-PLATE CABLES N.B. Before continuing with installation it is necessary to move the hood to a height of at least 650 mm from the cooker hob, using a support or the assistance of an-other person. This is essential, as the hood cables must necessarily be connected to the plate fi...
Page 12 - • Insert the cables into the safety knobs (
EN 1 12 • Attention to the direction of the plate fixed to the ceiling (the limit pawl on the plate fastened to the ceiling has a corresponding hole on the plate cover and on the hood canopy). • Insert the cables into the safety knobs ( c ) with the thread at the top. • Insert the cables into the ca...
Page 13 - • Pass the cables through the slots in the threaded pawls (
EN 1 13 • Pass the cables through the slots in the threaded pawls ( a ) and screw the cable locking screws ( b ) to the pawls them- selves. • When the operation has been completed the result must be as shown in the figure for all 4 ca-bles. • At this point we have all 4 cables con- nected to the pla...
Page 14 - supply using the respective power cables.
EN 1 14 • At this point it is possible to connect up the hood, and the lamp if there is one, to the power supply using the respective power cables. • Close the plate cover using the 3 screws removed previously and the wrench provided • At this point the Hood is sus- pended.
Page 15 - Connections; AIR OUTLET - DUCTING VERSION
EN 1 15 Connections AIR OUTLET - DUCTING VERSION To install the hood in the ducting version, please refer to the instructions provided in the ducting kit specific to the hood. AIR OUTLET – RECIRCULATION VERSION • Open the lighting unit by pulling on the notch provided. • Remove the grease filter. • ...
Page 16 - LEVELLING THE HOOD
EN 1 16 LEVELLING THE HOOD • The hood mobile unit must be levelled to allow the movement to operate properly. • The hood is levelled by adjusting the safety pawls. • Rest a spirit level on the hood. • When the safety knobs are pressed upwards, movement of the hood is “unlocked”. By in-serting or ext...
Page 17 - FIXING THE POWER SUPPLY CABLE
EN 1 17 FIXING THE POWER SUPPLY CABLE • Wind the power cable around its axis so that it forms a spiral from the mobile body to the plate in the ceiling. • It is important to do this to prevent the wire come out from the hood body during the closing of the hood • Take the cable clamp 3 provided. • In...
Page 18 - FITTING THE GLASS – CHIC-VANILLA MODELS; Electrical connection
EN 1 18 FITTING THE GLASS – CHIC-VANILLA MODELS • Take the lamps and insert them in the lamp holders. • They do not have to be screwed in, but simply inserted all the way. • Fix the glass 5 to the plate using the screws 12d and washers 22 in the top part. • Fix the glass elements together at the bot...
Page 19 - Control panel
EN 1 19 USE Control panel L T1 Button Function Display L Turns the lights On/Off. - T1 Hood Down Press for 2 seconds to raise the Hood. Press briefly to turn the Motor On/Off. On/Off Hood Up Press once: The Hood lowers. Press a second time: The Hood Stops. When the movement has been completed the mo...
Page 20 - REMOTE CONTROL
EN 2 20 REMOTE CONTROL The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included). • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. Control pan...
Page 21 - Grease filter; CLEANING METAL SELF- SUPPORTING GREASE FILTER; Activated Charcoal Filter (Recirculation Version); CHANGING
EN 2 21 MAINTENANCE Grease filter The filter must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. CLEANING METAL SELF- SUPPORTING GREASE FILTER • Open the lighting unit by pulling on the nocth. • Remove the filter one by one...
Page 22 - Lighting; LIGHT REPLACEMENT; • Remove the snap-on lamp cover by levering it from under the; Lighting Unit Lamps
EN 2 22 Lighting LIGHT REPLACEMENT 20 W halogen light. • Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. • Remove the halogen lamp from the lamp holder by pulling gently. • Replace the lamp with a new one of the same type, making sure that you ins...
Page 23 - Additional information for the installation technician; The front left cable must not be
EN 2 23 Additional information for the installation technician • Open the lighting unit by pulling on the notch provided. • Apply the label, indicated the type of lighting, on the Hood as indicated in the figure (Rif. A ). Procedure to be used in case of malfunction on the movement • Check that the ...
