Page 2 - YEAR WARRANTY REGISTRATION CARD
Please complete and mail. This card will ensure that your warranty is properly documented in our database. Complete Product Name:________________________________________________________________ Name:___________________________________________ E-Mail: _____________________________ Address:___________...
Page 4 - FCC COMPLIANCE STATEMENT:; • Reorient or relocate the receiving antenna
PRODUCT NAME MODEL NUMBER UltraATA 133/100 Pro CN2490 FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS BOPERATING ENVIRONMENT: FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) This device ...
Page 5 - iv; Contents; Chapter 1: Introduction
User's Manual iv Contents Chapter 1: Introduction 1-1 Unpacking the UltraATA 133/100 Pro ......................... 1-1 1-1.1 Static Electricity Precaution .............................. 1-21-1.2 Record the Serial Number ................................. 1-2 1-2 Introducing the UltraATA 133/100 Pro ....
Page 6 - About This Manual; This manual is comprised of the following sections:; Introduction
Contents v About This Manual T h e p u r p o s e o f t h i s m a n u a l i s t o i n t ro d u c e y o u t o y o u rUltraATA 133/100 Pro. It will guide you on how to install the cardand software for proper operation in your computer. Please savethis manual for future reference in the event you wish t...
Page 9 - Note; Leave the product in its static-resistant; Caution; Static electricity discharge may per-
1-2 User's Manual 1-1.1 Static Electricity Precaution One of the routine precautions you must be aware of whenworking with computer components is the problem of staticelectricity discharge. Note Leave the product in its static-resistant bag until you are ready to install it. Caution Static electrici...
Page 10 - Key Features and Benefits
Introduction 1-3 1-2 Introducing the UltraATA 133/100 Pro The UltraATA 133/100 Pro is an ultra high-speed dual channel UltraATA/133 controller board for use with Power Macs. It achievesburst data transfer rates up to 133MB/sec and supports drivecapacities greater than 137GB. And it also provides ful...
Page 11 - Board Layout
1-4 User's Manual 1 1 Figure 1-1. UltraATA 133/100 Pro Board Layout Ultra ATA 133/100 Connectors 1-2.3 Board Layout IDE2 IDE1 Ultra ATA/133/100 Chipset
Page 12 - Installation; Hardware Installation; Static Electricity Discharge may permanently damage
Installation 2-1 Chapter 2Installation This chapter will guide you through the installation of theUltraATA 133/100 Pro into your computer. 2-1 Hardware Installation General instructions for installing the card are provided below. Ifneeded, please refer to your computer’s reference manual for moreinf...
Page 13 - Device Connection
User's Manual 2-2 Note: Hold the board by its external edges only. Try to avoid touching the components, connectors or pins. 2-2 Device Connection The UltraATA 133/100 Pro is a dual channel Ultra ATA/133controller that supports up to four IDE hard disk drives or CD-R/RW drive. If you plan to use the...
Page 14 - Attach one connector on the long end of the Ultra ATA; When two hard disk drives are installed on the same IDE; The Ultra ATA ribbon cable has two connectors. If you
Installation 2-3 2. Attach one connector on the long end of the Ultra ATA ribbon cable to the board's IDE connector and the otherconnector(s) to your hard disk drive(s). Make sure pin 1 onthe cable (indicated by the colored stripe) matches pin 1 onthe board's IDE connector and your hard disk drive(s...
Page 15 - Software Installation; icon. Follow on-screen instructions to complete; click Mac OS 8.6 drive icon on the desktop.
User's Manual 2-4 2-3 Software Installation This section provides information on how to install the UltraATA133/100 Pro driver in your Power Mac. Please refer to the Mac OSmanual to familiarize yourself with Drive Setup and OSInstallation routines. 2-3.1 Driver Installation for Mac OS 8.6 For a fres...
Page 16 - OS Install; click Mac OS 9.x drive icon on the desktop.
Installation 2-5 2-3.2 Driver Installation for Mac OS 9.x For a fresh OS 9.x installation: 1. Install the UltraATA 133/100 Pro and attached drives.2. Boot up your computer with the Mac OS 9.x CD-ROM. Press and hold letter C on the keyboard while your system isbooting to boot from CD-ROM. 3. When Mac...
Page 17 - For a fresh OS X installation:; Mac OS X installation.; For systems that have OS X installed:; click Mac OS X drive icon on the desktop.
User's Manual 2-6 2-3.3 Driver Installation for Mac OS X For a fresh OS X installation: 1. Install the UltraATA 133/100 Pro and attached drives.2. Boot up your computer with the Mac OS X CD-ROM. Press and hold letter C on the keyboard while your system isbooting to boot from CD-ROM. 3. When Mac OS f...
Page 18 - Verifying Installation; for successful installation.; Click Apple logo located on the upper left corner of the; , shut down your system. Make sure the board is properly
Installation 2-7 2-4 Verifying Installation After you succesfully initialize the hard drive, new Untitleddrive(s) icon will appear on the desktop. Please check AppleSystem Profiler for successful installation. 2-4.1 Verify Mac OS 8.6/9.x Installation 1. Click Apple logo located on the upper left cor...
Page 20 - Technical Support & Product Return; Installation instructions from this user's manual
3-1 Technical Support & Product Return 3-1 Overview This chapter will give you instructions on how to obtainproduct information, contact technical support and returndefective product. This user's manual is written witheasy-to-understand instructions on how to configure andinstall this product in...
Page 21 - -3 Technical Support; SIIG’s; Online Support; Simply visit our web site at; SUPPORT; link. Our online support database is updated
3-2 User's Manual 3-3 Technical Support QUESTIONS? SIIG’s Online Support has the answers! Simply visit our web site at www.siig.com and click on the SUPPORT link. Our online support database is updated daily with new drivers and solutions. The answers to yourproblems could be just a few clicks away....
Page 22 - Step 2: Complete the RMA form; • Fill out your Return Merchandise Authorization (RMA); Step 3: Ship the Product
3-3 Technical Support & Product Return Step 2: Complete the RMA form • Fill out your Return Merchandise Authorization (RMA) form, and include it in the package with the product. • Properly pack the product for shipping. All software, cable(s) and other accessories that came with the originalpack...
Page 24 - RETURN MERCHANDISE AUTHORIZATION (RMA) FORM; LIMITED 5 YEAR WARRANTY
RETURN MERCHANDISE AUTHORIZATION (RMA) FORM RMA Number:_____________________________________ Date:__________________________________ Name:___________________________________________________________________________________ Company:______________________________________________________________________...