Quadra-Fire GARNET-D-CWL - Manual
Quadra-Fire GARNET-D-CWL – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – and Welcome to the Quadra-Fire Family; SAMPLE OF SERIAL NUMBER / SAFETY LABEL; Serial Number; L E; Manufactured Date
- Page 4 – Listing and Code Approvals; A. Appliance Certi cation; This installation must conform with local codes. In the; National; and the; CAN/CGA B149 Installation Codes; D. High Altitude Installations; WARNING; Model; F. Combustible Materials
- Page 6 – Getting Started; and national codes and regulations.; CAUTION; B. Tools and Supplies Needed; tools will apply to every installation.; • Installation and use of any damaged appliance or vent; Any such action may cause a re hazard.; warranty will be; Report damaged parts to dealer.
- Page 7 – Appliance Location and Clearances; A. Selecting Appliance Location; NOTE: For actual appliance dimensions refer to
- Page 8 – Page 8; Termination Locations; A. Vent Termination Minimum Clearances; specifi es minimum vent heights for various; • Do not pack air space with insulation or
- Page 9 – Page 9; = AREA WHERE TERMINAL IS NOT PERMITTED; public; Alcove Applications; IF EXTERIOR WALLS ARE FINISHED WITH
- Page 10 – Vent Information; A. Venting Components; DO NOT USE FIELD-FABRICATED VENTING; • Vent this appliance directly outside.; Figure; C. Measuring Standards; ALL vent confi guration specifi cations MUST be followed.
- Page 11 – EXCEPTIONS; Adjust
- Page 12 – F. Horizontal Termination; Type C - 45° Elbow in Corner Installation; Note; : Female ends of direct vent pipe/elbows are; Impaired Performance of Appliance.; • Ensure vent components are locked together correctly.
- Page 13 – Connect vent sections per installation instructions.; Improper support may allow vent to sag or separate.
- Page 14 – Some termination caps may cause the vent; Local codes may require installation of a cap; The attachment from the vent pipe to the vent
- Page 15 – Check the instructions below for maximum vertical rise; : Maximum number of 45° elbows permitted for a; G. Vertical Termination; et the gas appliance in its desired location. Drop a plumb; • Do not pack air space with insulation or other
- Page 16 – ) If an offset is necessary in the attic to avoid obstructions,
- Page 17 – • Any occupied areas above the first floor, including; For multi-story vertical installations, a ceiling firestop
- Page 18 – Trim Collar
- Page 19 – Sheet Metal Screws; and; Class A Metal Chimney; Remove existing chimney cap.
- Page 20 – Existing Masonry Chimney; Type D - Hearth Mount
- Page 22 – ). Mount the retro connector to the masonry wall using; wind termination cap on to the top adapter.
- Page 23 – the next page; Slim Line Wall Thimble; Assembling Slim Line Trim Ring and Heat Shield; Sharp Edges
- Page 24 – FIG. A 90 DEGREE ELBOW; FIG. C MINIMUM CLEARANCE; FIG. B 45 DEGREE ELBOW
- Page 25 – Gas Information; Converting to LP Gas; Lift off the appliance top and place it on a flat sur-; remove the wire clip.; Use a 5/32 in. Allen wrench to remove the pilot; PROPANE; Remove 2 screws
- Page 26 – Valve Regulator Replacement; Disconnect any electrical cords and; If the information in these instructions is; • Do no install a valve or regulator that has been
- Page 27 – • If substituting for these components, please consult local; We recommend; PRESSURE
- Page 28 – hazard or bodily injury.
- Page 29 – Electrical Information; A. Recommendation for Wire; DOES NOT; This appliance must be electrically wired and; National Electric Code ANSI/NFPA; or the; Canadian Electric Code, CSA; Wire Size
- Page 30 – • Wire must have high temperature insulation.; IGNITION MODULE; Switch; VALVE
- Page 31 – Appliance Setup; A. Remove Shipping Materials
- Page 32 – E. Positioning the Logs; The three piece log set is packed in the components
- Page 33 – H. Blower Installation; FROM THE KIT YOU WILL NEED:; Blower in mounting; G. Glass Replacement; Replacement is the reverse of the removal.; Handle glass assembly with care.; • Replace glass assembly as a complete
- Page 34 – Install the snap disc. A snap disc bracket is located; SNAP DISC; With the cast iron front of the appliance removed,
- Page 35 – Figure 8.15 Blower Wiring Diagram; BLACK
- Page 36 – K. Shutter Adjustment; J. Intake Damper Operation; OPEN
- Page 37 – Operating Instructions; A. Before Lighting Appliance; Fumes; PILOT IGNITOR; • Keep children away.
- Page 38 – C. Lighting Appliance; FOR YOUR SAFETY READ BEFORE LIGHTING; WHAT TO DO IF YOU SMELL GAS:; result causing property damage, personal injury or loss of life
- Page 39 – D. After Appliance is Lit; Initial Break-in Procedure; E. Frequently Asked Questions; ISSUE
- Page 40 – Troubleshooting; Symptom
- Page 41 – Check the burner orifi ce for stoppage. Remove stoppage.
- Page 42 – Longer operation without cleaning; When cleaning glass door:; USE CAUTION WHEN CLEANING/
- Page 43 – USE CAUTION WHEN CLEANING/HANDLING CERAMIC BURNER.; A. Maintenance Tasks
- Page 44 – Reference Materials; A. Appliance Dimension Diagram
- Page 45 – B. Vent Components Diagram; Figure 12.2 SL-D Series Vent Components
- Page 46 – C. Vent Components List
- Page 47 – TERMINATION CAPS & KITS
- Page 48 – Service Parts List; T h r e e - p ie c e L o g S e t
- Page 49 – Item
- Page 51 – Accessories; DESCRIPTION
- Page 52 – F. Service And Maintenance Log
- Page 53 – G. Homeowner’s Notes
- Page 55 – Lifetime Warranty; LIMITED LIFETIME WARRANTY
- Page 56 – CONTACT INFORMATION; DEALERSHIP WHERE PURCHASED:; Your Records for Model:; For the number of your nearest Quadra-Fire dealer; I. Contact Information
www.quadrafi re.com
August 1, 2008
R
GARNET-T
DIRECT VENT ROOM HEATER
Owner’s Manual
Installation and Operation
Model:
7016-127F
GARNET-MBK
GARNET-D-MBK
GARNET-D-PMH
GARNET-D-CSB
GARNET-D-CWL
O - T
O - T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
DO NOT DISCARD THIS MANUAL
CAUTION
• Important operating and
maintenance instructions
included.
• L e a v e t h i s m a n u a l w i t h
party responsible for use
and operation.
• Read, understand and
follow these instructions
for safe installation and
operation.
• Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- D o n o t t r y t o l i g h t a n y a p p l i a n c e .
Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
This appliance may be installed as an OEM installation in manufactured home (USA
only) or mobile home and must be installed in accordance with the manufacturer's
instructions and the manufactured home construction and safety standard,
Title 24
CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory-trained
professionals, or technicians supervised by an NFI
certifi ed professional.
DO NO
T
DISCARD
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber or gas
fi tter.
See Table of Contents for additional Commonwealth of Mas-
sachusetts requirements.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND
cool down.
Hot glass will cause
burns.
WARNING
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep
children
away
• CAREFULLY SUPERVISE children in the same room as
appliance
• Alert children and adults to hazards of high temperatures
High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other combustibles
away.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 Quadra-Fire · Garnet-T · 7016-127F August 1, 2008 and Welcome to the Quadra-Fire Family ! Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality, durability, and performance. This commitm...
Page 4 August 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 1 Listing and Code Approvals The product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recre-ational Vehicles” and "Gas Fired Appliances...
Page 6 August 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 2 Getting Started Check building codes prior to installation.• Installation MUST comply with local, regional, state and national codes and regulations. • Consult local building, fi re offi cials or authorities having jurisdiction about restric...
