Honeywell CT410A1019/E1 - User Manual
Honeywell CT410A1019/E1 Thermostat – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – REMOVE OLD THERMOSTAT; WARNING; WIRE AND MOUNT NEW
- Page 3 – CHECK OUT THERMOSTAT; SETTING THERMOSTAT
- Page 4 – LIMITED ONE-YEAR WARRANTY
- Page 7 – NOTICE D'INSTALLATION; Thermostats tension selecteur pour; Thermostat Honeywell; AVERTISSEMENT; AVIS DE RECYCLAGE; PRÉPARATION
- Page 8 – CÂBLAGE ET MONTAGE DU
- Page 10 – DÉPANNAGE
- Page 11 – ARANTIE LIMITÉE D'UN AN
INSTALLATION INSTRUCTIONS
® U.S. Registered Trademark
Copyright © 2004 Honeywell International Inc.
All Rights Reserved
69-1681EF-1
CT410A,B Line Voltage
Electric Heat Thermostats
CT410A provides single-line break.
CT410B provides double-line break.
Temperature Range: 5°C to 25°C (40°F to 80°F).
Electrical Ratings: 60 Hz noninductive.
22A at 120-240 Vac; 19A at 277 Vac.
Do-It-Yourself models.
Your Honeywell Thermostat
Your new Honeywell CT410 Electric Heating
Thermostat provides line voltage control of a
radiant cable, electric baseboard and resistive-
rated fan forced heaters within the ratings listed
above.
WARNING
120V to 240V Line Volt Electrical Shock
Hazard.
Can cause serious injury or death.
Do not install this line voltage control
unless you are completely familiar with
house wiring and installing line voltage
controls.
MERCURY NOTICE
If this control is replacing a control that
contains mercury in a sealed tube, do not
place you old control in the trash. Dispose
of properly.
Contact you local waste management
authority for instruction regarding recycling
and the proper disposal of a old control.
1 PREPARATION
❑
For accurate results when installing your
Honeywell thermostat, follow these instructions
step-by-step. It is recommended that as you
read, understand and complete each step, you
check it off with pencil or pen.
❑
Check thermostat suitability for your home
system after reviewing the ratings listed above.
❑
Be sure your heating system is working,
especially if it has been inoperative for a length
of time. If the system does not work, contact
your local electrician for assistance.
❑
Carefully unpack your new thermostat. To avoid
damage to the sensing element,
do not remove
the thermostat cover until wiring is completed.
❑
Save packages of screws, instructions, receipt
and proof-of-purchase.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CT410A,B LINE VOLTAGE ELECTRIC HEAT THERMOSTATS 69-1681EF—1 2 2 REMOVE OLD THERMOSTAT WARNING 120V to 240V Line Volt Electrical Shock Hazard.Can cause serious injury or death. Turn off power to the heating circuit at the main service panel before beginning installation. ❑ Remove cover of old thermos...
CT410A,B LINE VOLTAGE ELECTRIC HEAT THERMOSTATS 3 69-1681EF—1 4 CHECK OUT THERMOSTAT ❑ Turn on the power to the heating system. ❑ Turn setting knob fully clockwise; listen for clicking sound as the switch makes contact. The electric heater should begin operating. ❑ Turn knob fully counterclockwise; ...
CT410A,B LINE VOLTAGE ELECTRIC HEAT THERMOSTATS 69-1681EF—1 4 LIMITED ONE-YEAR WARRANTY Honeywell warrants this product to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time durin...
