Honeywell CT31A - User Manual

Honeywell CT31A

Honeywell CT31A Thermostat – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – Label wires and remove old wallplate
  • Page 3 – Mount thermostat base - CT31
  • Page 4 – Finish installation; Connect to
  • Page 5 – Temperature setting
  • Page 6 – Retrait de l’ancien thermostat; Vérifier le contenu du paquet :
  • Page 7 – Étiquetage des fils et retrait de la plaque de montage; Repérage de la position de montage
  • Page 8 – Installation du thermostat - CT31
  • Page 9 – Les étiquettes ne correspondent pas?; Raccordement des fils; Fils existants; Fin de l’installation
  • Page 10 – Garantie limitée de un an; Arrêt du système; Fonctionnement
  • Page 11 – Lista de comprobación previa a la instalación; Owner’s Manual; Remueva su viejo termostato
  • Page 12 – Rotule los cables y retire la vieja placa de montaje; Repérez la position de montage
  • Page 13 – Instalación de placa de montaje - CT30/CT33
  • Page 14 – ¿Los rótulos no coinciden?; Connecte los cables; Cables; Finalice la instalación
  • Page 15 – Garantía limitada de un año; Sistema apagado
Loading the manual

Owner’s Manual

English: Page 1

Mode d’emploi

Français : Page 6

Manual de Uso

Español: Página 11

CT30 Series

Low-Voltage Thermostat

M37781

69-2338EFS-04

M23786

MERCURY NOTICE

If your old thermostat contains

mercury, contact your local waste

management authority for proper

disposal instructions.

TURN OFF POWER

at heating/cooling system (or fuse/circuit-breaker panel).

Remove cover and thermostat, but leave wallplate with wires attached.

Is there a sealed tube containing mercury?

If so, see mercury notice below.

Leave wallplate in place.

Old thermostat

Cover

Getting started

Remove your old thermostat

Check package contents:

• Thermostat

• Coverplate

•

Wall anchors & screws (2 each)

•

Caution card

•

Wire labels

Before you begin, make sure you have:

•

No. 2 Phillips & small pocket screwdrivers

• Hammer

•

Level (optional)

• Pencil

•

Drill and bit (3/16” for drywall, 7/32” for

plaster)

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Honeywell CT31A

Summary

Page 2 - Label wires and remove old wallplate

CT30 Series • Owner's Manual 69-2338EFS—04 2 0 0 0 M23787 Wrap supplied labels securely around each wire. Do not let wires fall into wall opening! IGNORE WIRE COLORS: Use only letter designations to identify wire types. For CT31 : If your old thermostat has 5 or more wires (not counting terminals C ...

Page 3 - Mount thermostat base - CT31

English: Page 1 • Français : Page 6 • Español: Página 11 3 69-2338EFS—04 M29583 M29582 1. Drill holes at pencil-marked locations (3/16” holes for drywall, 7/32” holes for plaster). 2. Use hammer to tap anchors into holes until flush with wall. 3. Optional: Pull wires through cover plate (if needed t...

Page 4 - Finish installation; Connect to

CT30 Series • Owner's Manual 69-2338EFS—04 4 M29587A M29586 1. Mount thermostat on base and tighten three mounting screws (CT31 only). 2. Align the 3 tabs on the cover with slots on the thermostat, then push gently until the cover snaps into place. 3. Restore power at the heating/cooling system, or ...

Other Honeywell Thermostats Models