Honeywell T1 Pro - Installation Manual

Honeywell T1 Pro

Honeywell T1 Pro Thermostat – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – UWP Mounting System installation; For the rectangular cover plate:
  • Page 3 – UWP Wiring terminal designations; Power options; Rc; Setting Slider Tabs
  • Page 4 – Wiring conventional systems: forced air and hydronics; Wiring heat pump systems; Shaded areas below apply only to
  • Page 5 – Fan operation settings; Thermostat mounting; Menu
  • Page 7 – Specifications; Terminal; Heating
  • Page 8 – For assistance with this product, please visit; Customer assistance; Pull to remove the thermostat; CAUTION: MERCURY NOTICE; damage, avoid cycling the compressor quickly.; CAUTION: ELECTRICAL HAZARD; beginning installation.; CAUTION: ELECTRONIC WASTE NOTICE; consequences for the environment and human health.
  • Page 9 – Thermostat non; Notice d’installation; Installation de la plaque de couvercle en option
  • Page 10 – Installation du système de montage UWP
  • Page 11 – Options d’alimentation
  • Page 12 – Les cases grises ci-dessous s’appliquent uniquement au; Câblage des systèmes conventionnels : air forcé et hydronique; Câblage des systèmes à thermopompe
  • Page 13 – Montage du thermostat
  • Page 14 – Done; Options de configuration; REMARQUE
  • Page 15 – Caractéristiques techniques
  • Page 16 – Service à la clientèle; MISE EN GARDE : AVIS RELATIF AU MERCURE
  • Page 17 – Termostato no programable; Instalación de la placa de cubierta opcional
  • Page 18 – Instalación de la placa de cubierta rectangular:; Instalación del sistema de montaje con UWP
  • Page 19 – Opciones de suministro eléctrico; Configuración de las lengüetas de los controles deslizantes
  • Page 20 – Las siguientes áreas sombreadas se aplican solo al; Cableado de sistemas convencionales: aire forzado e hidrónico; Cableado de sistemas de bomba de calor
  • Page 21 – Configuraciones de funcionamiento del ventilador; Montaje del termostato
  • Page 22 – Opciones de configuración del instalador (ISU); las opciones estén disponibles.
  • Page 23 – Especificaciones; Clasificaciones eléctricas
  • Page 24 – Asistencia al cliente; Hale para retirar el termostato; PRECAUCIÓN: AVISO SOBRE EL MERCURIO; al equipo, evite encender y apagar rápidamente el compresor.; PRECAUCIÓN: PELIGRO DE ELECTROCUCIÓN; suministro eléctrico antes de comenzar la instalación.; PRECAUCIÓN: AVISO DE DESPERDICIO ELECTRÓNICO
Loading the manual
Page 1

Package Includes:

• T1 Pro Thermostat

• UWP™ Mounting System

• Decorative Cover Plate

• Screws and Anchors

• 2 AA Batteries

• Thermostat Literature

T1 Pro

Non-Programmable

Thermostat

Installation Instructions

–

+

Heat

Menu

Fan Auto

TH1110D2009,
TH1010D2000,
Read before installing

Optional Cover Plate installation

NOTE:

If Optional Cover Plate is not

required, see “UWP Mounting System

installation” on next page.
Use the

Optional Cover Plate

when

you need to cover paint gap from old

thermostat.
There are different cover plates

depending on when the thermostat was

manufactured.

For the square cover plate:

1. Separate the Cover Plate from

Mounting Plate.

2. Mount the Mounting Plate on to the

wall using any of the 8 screw holes.

Insert and tighten mounting screws

supplied with Cover Plate Kit. Do not

overtighten. See Figure 2. Make sure

the Mounting Plate is level.

3. Attach the UWP by hanging it on the

top hook of the Mounting Plate and

then snapping the bottom of the UWP

in place. See Figure 3.

4. Snap the Cover Plate onto the

Mounting Plate. See Figure 4.

Use supplied

screws and

wall anchors

4

3

2

1

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand
Honeywell
Model
T1 Pro
Document type
Installation Manual
Category
Thermostat
Language(s)
English, Spanish, French
Pages
24
Format
PDF

Summary

Page 2 - UWP Mounting System installation; For the rectangular cover plate:

2 UWP Mounting System installation Use 3x supplied screws (#8 1-1/2 for red anchors and #6 1-1/2 for yellow anchors) 1. Before starting, turn the power off at the breaker box or switch. Open package to find the UWP. See Figure 1. 2. Position the UWP on wall. Level and mark hole positions. See Figure...

Page 3 - UWP Wiring terminal designations; Power options; Rc; Setting Slider Tabs

3 Y 2 GC Y A Rc W K W 2 R L/A O/B AUX E UWP Wiring terminal designations L /A - A Not used for T1 thermostat. O/B Changeover Valve (TH1110D only) Y Compressor contactor (stage 1) AUX - W2 Not used for T1 thermostat. Y2 Not used for T1 thermostat. E Not used for T1 thermostat. G Fan Relay W Heat rela...

Page 4 - Wiring conventional systems: forced air and hydronics; Wiring heat pump systems; Shaded areas below apply only to

4 Wiring conventional systems: forced air and hydronics NOTES Wire specifications: Use 18- to 22-gauge thermostat wire. Shielded cable is not required. [1] Power supply. Provide disconnect means and overload protection as required. [2] Move R-Slider Tab on UWP to the R setting. For more information,...

Ask a question

Up to 3 photos. Max 5 MB each. Formats: JPG, JPEG, PNG, WebP.

Related manuals

Popular Honeywell Thermostats

More Honeywell Thermostats models