Heath Zenith SL-5514 - Manual
Heath Zenith SL-5514 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Turn power off at the fuse or circuit breaker.; turn power off
- Page 3 – SPECIFICATIONS; Bottom of Sensor; SENS
- Page 4 – TROUBLESHOOTING GUIDE; No Service Parts Available for this Product; ONE YEAR LIMITED WARRANTY
- Page 5 – FUNCIONAMIENTO; Resumen de las modalidades del; PRUEBA; Prueba
- Page 6 – INSTALACION; CUIDADO: Para evitar los peligros de incendio; Apague la energía en el fusible o cortacircuitos.
- Page 7 – Lo menos sensible; Parte de abajo del detector
- Page 8 – GUIA DE INvESTIGACION DE AvERIAS; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.; GARANTÍA LIMITADA A 1 AÑO
- Page 9 – garniture; Exigences; FONCTIONNEMENT; Résumé du mode de commutation
- Page 10 – D’É
- Page 11 – Bas du détecteur
- Page 12 – GUIDE DE DÉPANNAGE; GARANTIE LIMITÉE DE 1 AN; SERvICE TECHNIQUE; ner l’article au magasin.
© 2007 HeathCo LLC
595-5730-05
Twin Halogen Motion
Sensing Light Control
Model SL-5514
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight
hours.
Requirements
•
The light control requires 120-volts AC.
•
If you want to use Manual Mode, the control must
be wired through a switch.
•
Some codes require installation by a qualified
electrician.
•
This product is intended for use with the enclosed
gasket and with a junction box marked for use in
wet locations.
Cover Plate
Light Control
Sensor
3 Wire
Connectors
Gasket
6 Mounting
Screws (3 sizes)
Mounting Bolt
Mounting Strap
Rubber Plug
Plastic Hanger
2 Halogen Bulbs
This package includes:
OPERATION
* resets to Auto Mode at dawn.
Note:
When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
MANUAL MODE
ON-TIME
10 5 1
TEST
10 5 1
TEST
ON-TIME
TEST
... back on.
AUTO
1 Second
OFF
then...
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Mode:
On-Time
Works:
Day Night
Test
5 Seconds
x
x
Auto
1, 5, or 10 Min
x
Manual
Until Dawn*
x
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 595-5730-05 INSTALLATION For easy installation, select an existing light operated by a wall switch for replacement. For best performance, mount the fixture about 8 ft. (2.4 m) above the ground. W ire the L ight C ontroL ❒ Turn power off at the fuse or circuit breaker. ❒ Remove the existing light f...
3 595-5730-05 The detector is less sensitive to motion directly towards it and more sensitive to across motion. Least Sensitive Most Sensitive Sensor Motion Motion Avoid aiming the sensor at: • Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources co...
4 595-5730-05 POSSIBLE CAUSE 1. A lamp is positioned too close to the sensor or pointed at nearby objects that cause heat to trigger the sensor. (Reposition the lamp away from the sensor or nearby objects.) 2. Sensor is pointed toward a heat source like an air vent, dryer vent, or brightly-painted h...
