Field Controls CW-HD-2 - Manual
Field Controls CW-HD-2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Magnets; TESTING FOR HARDNESS AND IRON LEVELS; High Iron Concentration
- Page 3 – Figure 1; INSTALLATION
- Page 4 – ROPERLY WRAPPING THE ANTENNAE; Nominal Pipe Diameter; GPM
- Page 5 – OPERATION TIMETABLE FOR THE CLEARWAVETM; Scale begins to break down and come off water heater elements; OTES; used to aid the operation of a water softener.; ANUFACTURERS; The ClearWave; ATISFACTION
- Page 6 – For more information on the ClearWave
- Page 7 – Warranty Registration; Hardness; ppm’s if Known
CLEARWAVE
™
WATER CONDITIONER
MODEL CW-HD-2
The ClearWave
™
is the most advanced hi-tech computerized anti-scale device available today. It
operates by using a programmed ‘chip’ to constantly cycle through and induce over 200 different electro-
magnetic low frequency wave pulses into the water. These wave pulses produce water with remarkable
anti-scale properties, without adding salts or chemicals, at an operating cost for electricity of
approximately $25.00 per year.
P
OWER
S
PECIFICATIONS
:
18 VAC, 25 Watts, .22 Amps
HOW IT WORKS
Pure water contains nothing but H
2
0. But water, as it comes out of the ground, is rich in a multitude of
minerals. Minerals such as calcium and magnesium are the main components of hard water, and the
cause of scale formation and other problems.
There are three basic methods used to control the problem of hardness and specifically scale
formation.
I
ON
E
XCHANGE
:
One method is to remove the calcium and magnesium from the water through ion exchange (the
traditional water softener). This method requires the use of a resin filled tank with a high concentration of
salt ions. As the water flows through the resin tank the salt ions (typically sodium) are exchanged for the
calcium or magnesium ions. This lowers the concentration of the minerals that cause scale and therefore
inhibits scale formation.
C
HEMICAL
A
DDITION
:
A second method used to control hard water scale is the addition of chemicals (such as phosphates) to
the water. These materials chemically alter the scaling characteristics of the calcium or magnesium,
allowing the concentration of the minerals to stay the same while still reducing scale formation and its
affects.
Both of the above methods require the use of consumable materials to change the makeup of the water.
For these devices to function properly, the homeowner must continuously replenish the salts or chemicals
as well as perform periodic maintenance on the equipment. In addition to these inconveniences, the
chemicals and salts discharged into the effluent water present problems downstream to the municipal
water treatment facility and the environment. Many U.S. cities have been enacting and/or evaluating
environmental legislation to limit or reduce the levels of chemicals or salts that result from these types of
water treatment methods.
E
LECTRIC
P
OTENTIAL
:
A third method used to treat the hard water problems associated with scale utilizes changes in electrical
potential in the water to produce the affects of chemical addition. The electric potential applied changes
the scaling characteristics of the calcium or magnesium without the removal of these ions or the addition
of chemicals.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 Magnets Bar magnets were the first types of equipment used to generate electric potential changes in water. Bar magnets have been used with limited success to inhibit scale formation. The fixed magnetic field of a bar magnet creates electric potential changes in the water only when the water ...
Page 3 Figure 1 INSTALLATION W HERE TO INSTALL THE C LEAR W AVE ™ 1. For water supply applications, locate where the main water supply pipe enters the home or building. Point of use applications such as dishwashers, ice makers, boilers, water heaters etc., attach the ClearWave™ unit to the water sup...
Page 4 P ROPERLY WRAPPING THE ANTENNAE The antenna wrap around the water pipe on each end of the ClearWave™ (see Figure 1). A minimum of seven fully wrapped coils of the antenna wire, with each coil wrapped tightly against the pipe and pressed snugly against each other is required for best results (...
