Fanimation CRL4WH - User Manual

CRL4WH Remote Control

SPECIFICATION and INSTRUCTION SHEET

DESCRIPTION:

One Ceiling Fan & Light, 3 Speed Remote Control with Learn Receiver

ELECTRICAL SPECS:

FAN MODEL USED:

120 Volts, 60 Hertz, Fan 1.0 amp, Light Rating 190W (max.)

Incandescent or Halogen, 5 Wire Installation

May be used in conjunction with CWRL4 Wall Control

See Catalog or visit our website

www.fanimation.com

for more information

NOTE:

If fan or supply wires are different colors than indicated,

have this unit installed by a qualified electrician.

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advise, as it must be

grounded for safe operation.

INSTALLATION INSTRUCTIONS:

Ceiling fan must be set at HIGH speed and light kit (If any) at

1.

the ON position by pressing the “Light Switch” after installation.

Install Receiver in the Hanger Bracket:

2.

•

Slide remote Receiver into the Hanger Bracket (Figure 1).

• Connect wires as indicated: (Figure 2)

–Green Hanger Bracket and Hanger Ball wires to BARE (ground) wire.

–BLACK Receiver Unit wire (AC IN L) to BLACK supply wire.

–WHITE Receiver Unit wire (AC IN N). to WHITE supply wire.

–WHITE Receiver Unit wire (TO MOTOR N) to WHITE fan wire.

–BLACK Receiver Unit wire (TO MOTOR L) to BLACK fan wire.

–BLUE Receiver Unit wire (FOR LIGHT DOWN) to BLUE light wire.

•

Position all connected wires and receiver antenna to allow

installation of ceiling canopy.

•

Using canopy screws threaded into the hanger bracket reinstall

ceiling canopy.

•

Restore electrical power

IMPORTANT:

YOU MUST SET YOUR CEILING FAN TO HIGH SPEED AND LIGHT KIT

(IF ANY) TO THE ON POSITION BEFORE OPERATING YOUR REMOTE CONTROL.

Figure 2

Receiver Unit

Ceiling

Bracket

(Open End)

NOTE:

Receiver wires omitted for clarity.

Figure 1

Figure 3

BLK-ANT

BL-AC IN L

WH-AC IN N

BLUE-FOR LIGHT DOWN

BLK-TO MOTOR L

WH-TO MOTOR N

GRN or BARE GROUND

GRN from hanger bal

l

GRN from bracket

120 VAC SUPPLY

(User Supplied)

(DO NOT CUT)

Figure 2

LEARN MODE PROCESS:

Control and receiver have been factory programmed. If replacing the

1.

transmitter or receiver, the learn mode process will need to be used.

After installing the unit and restoring power to your fan, open the

2.

battery cover (with battery, DC12V/A23 1pc, installed) and press

and hold the ”LEARNING BUTTON” 1~3seconds with a ball-point

pen or similar object. FAN will turn off and then turn to medium

speed, which indicates that the learning process has completed.

IMPORTANT: You must press the “LEARNING BUTTON”

within 60 seconds of restoring power to the fan. Remote

does not need to be re-learned when replacing the battery.

Please note, the remote can learn multiple receivers.

4.

60 second time limit should eliminate need for this.

If light kit has CFL bulbs, please slide the “light dimmer function

3.

select switch” to on/off position. If installed incandescent light

bulbs onto ceiling fan, please slide the “light dimmer function

select switch” to dimmer position.

Figure 3

10983 Bennett Parkway

Zionsville, IN 46077

(888) 567-2055 • FAX (866) 482-5215

Outside U.S. call (317) 733-4113

Visit Our Website @ www.fanimation.com

Copyright 2010 Fanimation

2010/02

REMOTE FUNCTIONS:

LIGHT: ON/OFF- Press and release immediately to turn on or

off the light.

DIMMER: Press and hold to dim or brighten light to the desired level

and release—feature can not be used with CFL bulbs

OFF:

Turns off the fan

HIGH:

Turns fan to high speed

MED:

Turns fan to medium speed

LOW:

Turns fan to low speed

LIGHT LOW FAN OFF

MEDIUM HIGH

WARNING

Check to see that all connections are tight, including ground,

and that no bare wire is visible at the wire connectors,

except for the ground wire. Do not operate fan until the

blades is in place. Noise and fan damage could result.

LEARNING

BUTTON

DIMMER

ON/OFF

LIGHT DIMMER FUNCTION

SELECT SWITCH

Install Remote Control

Wall Mount Holder

with two screws.