Crimestopper EZ-10 - Manual
Crimestopper EZ-10 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – VENDORS
- Page 3 – REMOTE CONTROL DIAGRAMS; LOCK; Flashlight; “COOLFLASH” BLUE LED FLASHLIGHT; NOTE: REMOTE START BUTTON DELAY
- Page 4 – REMOTE ENGINE CONTROL; REMOTE ENGINE STARTING - SUCCESSFUL START:; IGN; REMOTE ENGINE STARTING - UNSUCCESSFUL START; NO FURTHER; TURNING OFF A REMOTE STARTED ENGINE:; RUN TIME RESET
- Page 5 – ENTERING YOUR REMOTE STARTED VEHICLE:; now controlling your vehicle.
- Page 6 – INFINITY RUN MODE; INDEFINITELY after the programmed run time elapses; INFINITY RUN MODE – EXITING THE VEHICLE:; then press and release the remote start button a second time.; ENTERING A VEHICLE DURING IDLE-DOWN or INFINITY RUN MODES:; See “Entering Your Remote Started Vehicle” on Last page.; SELECTABLE HOURLY COLD-START MODE – EXITING THE VEHICLE:
- Page 7 – engine should remain running for the selected number of minutes.
- Page 8 – CONVENIENCE AND SAFETY FEATURES; HOOD OPEN SAFETY (Requires grounding hood pin installation)
- Page 9 – BRAKE PEDAL RESET; TRANSMITTER PROGRAMMING; get 2 light flashes indicating the unit is waiting for a 2; unit will flash 3 times indicating its waiting for the 3; code and so on. If all 4 codes are learned, the unit will
- Page 10 – TRANSMITTER PROGRAM DIAGRAM:
- Page 11 – TROUBLESHOOTING: “BEFORE YOU CALL” SECTION; UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY):
- Page 12 – UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:
EZ-30 / EZ-10
REMOTE ENGINE STARTING SYSTEM
OPERATING INSTRUCTIONS
INTRODUCTION
**IMPORTANT NOTES:- FOR EZ-10 MODEL ONLY**
The EZ-10 Model is for remote starting purposes only. It has NO keyless entry functions. Any information in this
manual pertaining to remote keyless entry functions, door lock & door unlock applies only to the EZ-30 model.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY:
These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, Brake Reset. For programming, the hood pin and program button are required.
-OPTIONAL:
These features are to be connected only if desired or agreed upon by the customer and the
installing dealer i.e. Anti-Grind, Turbo timer, etc. These features may also require additional parts and/or labor
fees. Consult with your installer beforehand to be sure of what is going to be installed with your particular system.
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [email protected]
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV A - 08.2004
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Remote Control Diagrams………...……………………………………………………………………………...…….3 Remote Engine Control…………….…..…………………………………………………………………….……….4-6 Turbo Timer Mode……………………………….……………………………………...………………………………7 Convenience and Saf...
REMOTE CONTROL DIAGRAMS #1 #2 #3 LOCK ENGINE UNLOCK VEHICLE #2 FLASHLIGHT START/STOP EZ-30 EngineStart/Stop Flashlight Vehicle#2 EZ-10 System EZ-30 SYSTEM The transmitter supplied with the EZ-30 system has 5 buttons total. The button configuration of the EZ-30 is Factory-set and unchangeable. See Pa...
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1 second. 2) Parking lights flash once; return solid, and the Ignition/Acc circuits turn on. 3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off ...
