Crimestopper CS-883 OEM - Manuals

Page 2 - TABLE OF CONTENTS; Installation Modes “A” & “B”.........................................................................................................6-7; INSTALLATION PRECAUTIONS & WARNINGS; BEFORE BEGINNING; with brake, and gas pedals, steering; COMPONENT MOUNTING; Mount button in a hidden but accessible location. It is

2 TABLE OF CONTENTS Installation Cautions & Component Mounting…….……………….…………………………………………………..2 Wiring………………………………………………………………………………………………..…………….…………3-5 Installation Modes “A” & “B”……………………………………………………………………………………………6-7 System Wiring Diagram………………………………………………………………………………….………………….8 Programma...

Page 3 - WIRING; NORMALLY OPEN; BLACK WIRE: SYSTEM CHASSIS GROUND

3 WIRING (2) VIOLET WIRES: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #1 NORMALLY OPEN These wires come directly from the terminals of an on-board Relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Selected the circuit you want to interrupt, cut it, and connect each cut end to a VIOLET ...

Page 4 - YELLOW WIRE: +12 VOLTS IGNITION SWITCHED; Connect to door pin activation circuit in vehicle:

4 WIRING PINK & PINK/WHITE WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2 NORMALLY OPEN These wires come directly from the terminals of an on-board relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Select the circuit you want to immobilize, cut it, and connect one end to the P...

Page 5 - **SEE DOOR LOCK MOTOR / VALIDATION WIRE CONNECTIONS NEXT PAGE; The sensor supplied with this system does not

5 WIRING GREEN WIRE: (-) HOOD/TRUNK TRIGGER Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read ground when open. If no existing switches are available, new pin switches may be installed. Note: DO NOT mount new pin switches in water p...

Page 6 - MODE A; is the default mode and is used for most vehicles.

6 NEGATIVE VALIDATION INPUTS (TOP EDGE OF 883 MODULE) POSITIVE VALIDATION INPUTS (TOP EDGE OF 883 MODULE) INSTALLATION MODE “A” (Most Vehicles) MODE A is the default mode and is used for most vehicles. This mode requires 4-W ires to be connected for proper operation: Yellow/Black and Blue/Black conn...

Page 7 - INSTALLATION MODE “B”; MODE B; Brown; Unlock

7 INSTALLATION MODE “B” MODE B is used for vehicles with single wire locking systems that are often called “Data Bus” or “Multi-Plex” vehicles. These vehicles include many late model Dodge/Chrysler Vehicles, 2003 GM Truck, SUV’s, and 1996-2003 Jeep Grand Cherokee, and others. This mode must be progr...

Page 8 - SYSTEM WIRING DIAGRAM

8 SYSTEM WIRING DIAGRAM +12V R E D/ W H IT E 12V START INPUT IGNITION KILL RELAY 3 0 BLACK/WHITE WHITE/RED BLACK PARKING LIGHTS HORN OR SIREN GND 10A FUSE WHITE 10A FUSE WHITE CONNECTS TO POSITIVE SIDE OF TRUNK RELEASE OF TRUNK SOLENOID DOOR TRIGGER INPUT (+/-) HOOD/TRUNK TRIGGER INPUT (-) 15A FUSE ...

Page 9 - PROGRAMMABLE OPTIONS; OPTION PROGRAMMING CHART

9 PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds. 2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming mode. 3. Within 20 seconds, press the Override/Program button the number of times ...

Page 10 - ADJUSTABLE HORN PULSE

10 PROGRAMMABLE OPTIONS 2. DOOR WARNING DELAY This setting changes the delay time (10 or 60 seconds) in which the alarm system begins to monitor the Door circuit. This option can prevent the alarm from giving warning chirps on vehicles with a delayed dome light. 3. ADJUSTABLE HORN PULSE Some vehicle...

Page 11 - OPERATING INSTRUCTIONS; ARMING

11 OPERATING INSTRUCTIONS ARMING To arm the alarm and lock the doors, press the Lock button of your Factory Keyless Remote Control. The 883 OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will chirp once. After 3 seconds, the LED indicator wi...

Page 12 - OPERATING INSRUCTIONS; VALET MODE

12 OPERATING INSRUCTIONS VALET MODE To disable alarm functions of the 883 system, turn the Ignition ON and press the override/program button 3 times within 8 seconds. Turn off ignition, after 8 seconds, the dash LED turns on solid as an indicator that the system is in valet mode. Repeat these steps ...